Planet WGSW-50040 User Manual Page 133
- Page / 437
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
untagged frame enters a Trunk port, the port will tag the untagged frame with the native PVID set
with this commands for VLAN forwarding.
Example:
Set the native VLAN for a Trunk port to 100.
Switch(config)#interface ethernet 1/5
Switch(Config-If-Ethernet1/5)#switchport mode trunk
Switch(Config-If-Ethernet1/5)#switchport trunk native vlan 100
Switch(Config-If-Ethernet1/5)#exit
7.1.21 vlan
Command:
vlan WORD
no vlan WORD
Function:
Create VLANs and enter VLAN configuration mode. If using ';' and '-' connect with multi-VLANs,
then only create these VLANs. If only existing VLAN, then enter VLAN configuration mode; if the
VLAN is not exist, then create VLAN and enter VLAN configuration mode. In VLAN Mode, the user
can set VLAN name and assign the switch ports to the VLAN. The no command deletes specified
VLANs.
Parameter:
WORD is the VLAN ID to be created/deleted, valid range is 1 to 4094, connect with ';' and '-'.
Command mode:
Global Mode.
Default:
Only VLAN1 is set by default.
Usage Guide:
VLAN1 is the default VLAN and cannot be configured or deleted by the user. The maximal VLAN
number is 4094. It should be noted that dynamic VLANs learnt by GVRP cannot be deleted by this
command.
Example:
Create VLAN100 and enter the configuration mode for VLAN 100.
Switch(config)#vlan 100
Switch(Config-Vlan100)#
7.1.22 vlan ingress enable
- WGSW-50040 1
- Content 2
- Chapter 1 Commands for 22
- Basic Switch Configuration 22
- 1.1.2 clock set 23
- 1.1.3 config 23
- 1.1.4 debug ssh-server 24
- 1.1.5 enable 24
- 1.1.6 enable password 25
- 1.1.7 exec-timeout 25
- 1.1.8 end 26
- 1.1.9 exit 26
- 1.1.10 help 27
- 1.1.11 hostname 28
- 1.1.12 ip host 28
- 1.1.13 ipv6 host 29
- 1.1.14 ip http server 29
- 1.1.15 language 30
- 1.1.16 login 30
- 1.1.17 password 31
- 1.1.18 reload 31
- 1.1.21 sysContact 33
- 1.1.22 sysLocation 33
- 1.1.23 set default 34
- 1.1.24 setup 34
- 1.1.25 show clock 35
- 1.1.26 show temperature 35
- 1.1.27 show tech-support 36
- 1.1.28 show version 36
- 1.1.29 username 36
- 1.1.30 web language 37
- 1.1.31 write 38
- 1.2 Commands for Telnet 38
- 1.2.6 authentication 42
- 1.2.7 terminal length 43
- 1.2.8 terminal monitor 43
- 1.2.9 telnet 44
- 1.2.10 telnet server enable 45
- 1.2.13 ssh-server enable 46
- 1.2.16 ssh-server timeout 48
- 1.2.17 show ssh-server 48
- 1.2.18 show telnet login 49
- 1.3.1 interface vlan 49
- 1.3.2 ip address 50
- 1.3.3 ipv6 address 51
- 1.3.4 ip bootp-client enable 51
- 1.3.5 ip dhcp-client enable 52
- 1.4 Commands for SNMP 53
- 1.4.1 debug snmp mib 53
- 1.4.2 debug snmp kernel 53
- 1.4.3 rmon enable 54
- 1.4.4 show snmp 54
- 1.4.5 show snmp engineid 56
- 1.4.6 show snmp group 56
- 1.4.7 show snmp mib 57
- 1.4.8 show snmp status 57
- 1.4.9 show snmp user 58
- 1.4.10 show snmp view 58
- 1.4.11 snmp-server community 59
- 1.4.12 snmp-server enable 60
- 1.4.14 snmp-server engineid 61
- 1.4.15 snmp-server group 62
- 1.4.16 snmp-server host 63
- 1.4.19 snmp-server view 65
- 1.4.20 snmp-server user 66
- 1.5.1 copy（FTP） 67
- 1.5.2 copy（TFTP） 68
- 1.5.3 ftp-dir 69
- 1.5.4 ftp-server enable 70
- 1.5.5 ftp-server timeout 70
- 1.5.6 ip ftp 71
- 1.5.7 show ftp 72
- 1.5.8 show tftp 72
- 1.5.9 tftp-server enable 73
- Chapter 2 Commands for 75
- Cluster 75
- 2.3 cluster commander 76
- 2.4 cluster ip-pool 77
- 2.7 cluster member 79
- 2.9 cluster reset member 81
- 2.10 cluster run 81
- 2.11 cluster update member 82
- 2.12 debug cluster 83
- 2.13 debug cluster packets 84
- 2.14 show cluster 84
- 2.15 show cluster members 85
- 2.16 show cluster candidates 86
- 2.17 show cluster topology 87
- 2.18 rcommand commander 89
- 2.19 rcommand member 90
- Chapter 3 Commands for 91
- Network Port Configuration 91
- 3.1.2 combo-forced-mode 92
- 3.1.4 flow control 94
- 3.1.5 interface ethernet 94
- 3.1.6 loopback 95
- 3.1.7 mdi 95
- 3.1.8 name 96
- 3.1.9 negotiation 97
- 3.1.10 port-scan-mode 97
- 3.1.11 rate-suppression 98
- 3.1.12 rate-violation 99
- 3.1.13 show interface 100
- 3.1.14 shutdown 103
- 3.1.15 speed-duplex 104
- Chapter 4 Commands for 106
- Port Loopback Detection 106
- Function 106
- 4.5 show loopback-detection 109
- 4.6 debug loopback-detection 109
- Chapter 5 Commands for 111
- Port Channel 111
- 5.3 port-group 112
- 5.4 port-group mode 113
- 5.5 show port-group 114
- Chapter 6 Commands for 118
- Chapter 7 VLAN 119
- Configuration 119
- 7.1.3 dot1q-tunnel tpid 120
- 7.1.4 gvrp 121
- 7.1.5 garp timer hold 122
- 7.1.6 garp timer join 122
- 7.1.7 garp timer leave 123
- 7.1.8 garp timer leaveall 123
- 7.1.9 name 124
- 7.1.10 private-vlan 125
- 7.1.12 show dot1q-tunnel 127
- 7.1.13 show garp 127
- 7.1.14 show gvrp 128
- 7.1.15 show vlan 128
- 7.1.17 switchport interface 130
- 7.1.18 switchport mode 131
- 7.1.21 vlan 133
- 7.1.22 vlan ingress enable 133
- 7.2.3 mac-vlan 135
- 7.2.4 mac-vlan vlan 136
- 7.2.5 protocol-vlan 136
- 7.2.7 show mac-vlan 138
- 7.2.9 show protocol-vlan 139
- 7.2.10 show subnet-vlan 139
- 7.2.12 subnet-vlan 140
- 7.3.1 show voice-vlan 143
- 7.3.3 voice-vlan 144
- 7.3.4 voice-vlan vlan 145
- Chapter 8 Commands for 146
- MAC Address Table 146
- 8.1.3 show mac-address-table 147
- 8.2.2 show port-security 149
- Chapter 9 Commands for 157
- 9.1.3 instance vlan 158
- 9.1.4 name 158
- 9.1.5 revision-level 159
- 9.1.6 spanning-tree 160
- 9.1.10 spanning-tree maxage 162
- 9.1.11 spanning-tree max-hop 163
- 9.1.12 spanning-tree mcheck 163
- 9.1.13 spanning-tree mode 164
- 9.1.21 spanning-tree format 170
- 9.2.1 show spanning-tree 173
- 9.2.3 show mst-pending 176
- 9.2.4 debug spanning-tree 177
- Chapter 10 Commands for 179
- 10.3 class-map 180
- 10.5 match 181
- 10.6 mls qos cos 183
- 10.7 mls qos map 183
- 10.8 mls qos queue algorithm 185
- 10.12 mls qos trust 188
- 10.13 policy 188
- 10.14 policy aggregate 190
- 10.15 policy-map 191
- 10.16 set 192
- 10.17 service-policy input 193
- 10.19 show class-map 194
- 10.20 show policy-map 195
- 10.21 show mls qos interface 196
- 10.22 show mls qos maps 199
- 10.23 show mls qos vlan 201
- Chapter 11 Commands for 202
- Flow-based Redirection 202
- Chapter 12 Commands for 204
- Layer 3 Forwarding 204
- 12.1.3 ip default-gatway 205
- 12.1.4 debug ip packet 206
- 12.1.5 show ip traffic 206
- 12.1.6 show ip route 209
- 12.2.1 clear ipv6 neighbor 210
- 12.2.2 debug ipv6 packet 210
- 12.2.3 debug ipv6 icmp 211
- 12.2.4 debug ipv6 nd 212
- 12.2.5 ipv6 default-gateway 212
- 12.2.6 ipv6 address 213
- 12.2.7 ipv6 redirect 214
- 12.2.8 ipv6 nd dad attempts 214
- 12.2.9 ipv6 nd ns-interval 215
- 12.2.10 ipv6 nd suppress-ra 215
- 12.2.11 ipv6 nd ra-lifetime 216
- 12.2.14 ipv6 nd prefix 218
- 12.2.16 show ipv6 interface 219
- 12.2.15 ipv6 neighbor 219
- 12.2.17 show ipv6 route 221
- 12.2.18 show ipv6 neighbors 222
- 12.2.19 show ipv6 traffic 223
- 12.2.20 show ipv6 enable 224
- 12.2.21 show ipv6 redirect 225
- 12.3.1 arp 225
- 12.3.2 clear arp-cache 226
- 12.3.3 debug arp 226
- 12.3.4 show arp 227
- 12.3.5 show arp traffic 228
- Chapter 13 Commands for 230
- ARP Scanning Prevention 230
- 13.4 anti-arpscan trust 232
- 13.5 anti-arpscan trust ip 232
- 13.8 anti-arpscan log enable 234
- 13.10 show anti-arpscan 235
- 13.11 debug anti-arpscan 237
- Chapter 14 Command for 238
- ARP GUARD 238
- Chapter 15 Commands for 239
- 15.1.5 client-identifier 241
- 15.1.6 debug ip dhcp server 242
- 15.1.7 default-router 242
- 15.1.8 dns-server 243
- 15.1.9 domain-name 243
- 15.1.10 hardware-address 244
- 15.1.11 host 245
- 15.1.14 ip dhcp pool 247
- 15.1.16 ip dhcp ping packets 248
- 15.1.17 ip dhcp ping timeout 249
- 15.1.18 lease 249
- 15.1.19 netbios-name-server 250
- 15.1.20 netbios-node-type 251
- 15.1.21 network-address 251
- 15.1.22 next-server 252
- 15.1.23 option 253
- 15.1.24 service dhcp 253
- 15.1.25 show ip dhcp binding 254
- Chapter 16 Commands for 257
- DHCP Snooping 257
- 16.6 ip dhcp snooping 259
- 16.13 ip dhcp snooping trust 264
- 16.19 enable trustview key 268
- 16.21 ip user helper-address 269
- 16.22 show trustview status 270
- 16.23 show ip dhcp snooping 271
- Chapter 17 Commands for 276
- DHCP Snooping option 82 276
- Chapter 18 IPv4 Multicast 277
- Protocol 277
- 18.1.6 ip multicast policy 281
- 18.2.4 ip igmp snooping 288
- 18.2.5 ip igmp snooping vlan 288
- 18.2.9 ip igmp snooping vlan 291
- Chapter 19 IPv6 Multicast 299
- 19.1.4 ipv6 mld snooping 300
- Chapter 20 Commands for 311
- Multicast VLAN 311
- Chapter 21 Commands for 313
- 21.2 absolute start 314
- 21.9 firewall 322
- 21.10 firewall default 323
- 21.11 ip access extended 323
- 21.12 ip access standard 324
- 21.13 ipv6 access-list 325
- 21.14 ipv6 access standard 325
- 21.16 mac access extended 327
- 21.17 mac-ip access extended 328
- 21.23 show access-lists 335
- 21.24 show access-group 336
- 21.25 show firewall 337
- 21.26 show ipv6 access-lists 337
- 21.27 show time-range 338
- 21.28 time-range 339
- Chapter 22 Commands for 340
- 22.3 debug dot1x fsm 341
- 22.4 debug dot1x packet 342
- 22.5 dot1x accept-mac 342
- 22.6 dot1x eapor enable 343
- 22.7 dot1x enable 344
- 22.8 dot1x ipv6 passthrough 344
- 22.9 dot1x guest-vlan 345
- 22.10 dot1x macfilter enable 346
- 22.11 dot1x max-req 347
- 22.15 dot1x port-control 349
- 22.16 dot1x port-method 350
- 22.18 dot1x re-authenticate 352
- 22.23 dot1x unicast enable 355
- 22.26 dot1x web redirect 356
- 22.28 show dot1x 358
- Chapter 23 Commands for 361
- Function of Port, MAC in 361
- VLAN and IP 361
- 23.6 debug vlan mac count 365
- Chapter 24 Commands for 366
- AM Configuration 366
- 24.3 am ip-pool 367
- 24.4 am mac-ip-pool 367
- 24.5 no am all 368
- 24.6 show am 368
- Chapter 25 Commands for 370
- Security Feature 370
- Chapter 26 Commands for 375
- TACACS+ 375
- 26.2 tacacs-server key 376
- 26.3 tacacs-server nas-ipv4 376
- 26.4 tacacs-server timeout 377
- 26.5 debug tacacs-server 378
- Chapter 27 Commands for 379
- 27.3 aaa-accounting update 380
- 27.4 debug aaa packet 380
- 27.7 debug aaa detail event 382
- 27.8 debug aaa error 383
- 27.9 radius nas-ipv4 383
- 27.10 radius nas-ipv6 384
- 27.14 radius-server key 388
- 27.16 radius-server timeout 389
- 27.20 show aaa config 392
- 27.21 show radius count 393
- Chapter 28 Commands for 394
- 28.2 clear mrpp statistics 395
- 28.3 debug mrpp 395
- 28.4 enable 396
- 28.5 fail-timer 397
- 28.6 hello-timer 397
- 28.7 mrpp enable 398
- 28.8 mrpp ring 399
- 28.9 mrpp ring primary-port 399
- 28.11 node-mode 400
- 28.12 show mrpp 401
- 28.13 show mrpp statistics 401
- Chapter 29 Commands for 402
- Mirroring Configuration 402
- Chapter 30 Commands for 405
- 30.2 sflow agent-address 406
- 30.3 sflow priority 407
- 30.4 sflow header-len 407
- 30.5 sflow data-len 408
- 30.6 sflow counter-interval 408
- 30.7 sflow rate 409
- 30.8 show sflow 410
- Chapter 31 Commands for 411
- 31.2 sntp server 412
- 31.3 sntp polltime 413
- 31.4 sntp timezone 413
- 31.5 show sntp 414
- Chapter 32 Commands for 415
- 32.4 ping 417
- 32.5 ping6 419
- 32.6 show debugging 421
- 32.7 show flash 421
- 32.8 show history 422
- 32.9 show logging buffered 422
- 32.10 show memory 423
- 32.11 show running-config 424
- 32.12 show startup-config 424
- 32.14 show tcp 426
- 32.15 show telnet login 426
- 32.16 show tech-support 427
- 32.17 show udp 427
- 32.18 show version 428
- 32.19 traceroute 428
- 32.20 traceroute6 429
- Chapter 33 Commands for 431
- Reload Switch after 431
- Specified Time 431
- 33.3 show reload 432
- Chapter 34 Commands for 433
- Debugging and Diagnosis 433
- Sent by CPU 433
- 34.5 show cpu-rx protocol 435
- 34.6 debug driver 436
- EC Declaration of Conformity 437
Related products and manuals for Routers Planet WGSW-50040
Routers Planet WGSW-5242 User Manual
(286 pages)
(286 pages)
Routers Planet WGSW-52040 User Manual
(505 pages)
(505 pages)
Routers Planet XGS3-24040 User Manual
(2 pages)
(2 pages)
Routers Planet XGS3-24040 User Manual
(16 pages)
(16 pages)
Routers Planet WGSW-52040 User Manual
(876 pages)
(876 pages)
Routers Planet XGS3-24040 User Manual
(582 pages)
(582 pages)
Routers Planet XGS3-24040 User Manual
(869 pages)
(869 pages)
Routers Planet XGS3-24042 User Manual
(721 pages)
(721 pages)
Routers Planet XGS3-42000R User Manual
(2 pages)
(2 pages)
Routers Planet XGS3-42000R User Manual
(16 pages)
(16 pages)
Routers Planet XGSW-28040 User Manual
(12 pages)
(12 pages)
Routers Planet EPN-103 User Manual
(20 pages)
(20 pages)
Routers Planet EPL-1000 User Manual
(20 pages)
(20 pages)
Routers Planet EPL-2000 User Manual
(20 pages)
(20 pages)
Routers Planet EPL-2000 User Manual
(81 pages)
(81 pages)
Routers Planet EPN-102 User Manual
(2 pages)
(2 pages)
Routers Planet EPN-102 User Manual
(17 pages)
(17 pages)
Routers Planet BSP-300 User Manual
(11 pages)
(11 pages)
Routers Planet BSP-300 User Manual
(35 pages)
(35 pages)
Routers Planet HPOE-1200G User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 2.360 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals