Planet BSP-300 User Manual

Industrial Solar Power PoE Switch ► BSP-300

 User’s Manual of BSP-3009 System  Smart Power Management System - Co-working with 300 watts solar PV kit and batt

 User’s Manual of BSP-300102.4 SpecificationProductBSP‐300HardwareSpecificationNetworkConnector3‐PortRJ‐45

 User’s Manual of BSP-30011Max.solararrayVoc60VDCMax.operatingvoltage45VDCTota lcurrentconsumptionWhile

User’s Manual of BSP-30012SystemUnitOperatingTemperature‐20~60DegreeCStorageTemp erature‐40~90DegreeC

2.5 Physical Description Front view SystemLED FAULT LED PV In  10/100/ 1000Base-T portBattery In / Out 10/100/1000Base-T PoE port x

 User’s Manual of BSP-30014LED Definition LED Status Description Slow Blink System On. System Fast Blink The ba

 User’s Manual of BSP-300152.6 Application Solar PoE Power Supply for Long Distance Wireless Surveillance Solution P

 User’s Manual of BSP-30016By working with a pair of serial over Ethernet Media Converter and the Wireless transmiss

 User’s Manual of BSP-30017Chapter 3. Basic Setup 3.1 Hardware Installation 3.1.1 Safety Precautions Please read bef

 User’s Manual of BSP-30018Step 1. Install BSP-300 Fix BSP-300 to desired location with wall mount fixture. NOTE: 1

User’s Manual of BSP-3001CopyrightCopyright © 2012 by PLANET Technology Corp. All rights reserved. No part of this

 User’s Manual of BSP-30019 (1) Connect the negative electrode of the battery to the terminal for the negative elect

 User’s Manual of BSP-30020NOTE: 1. Be noted for the thickness of electric wire and please refer to the section - R

 User’s Manual of BSP-30021Step 5. Connect other device (1) Connect any other network device to Port 3 of BSP-30

 User’s Manual of BSP-300223.2.1 Initial Utility Installation Install the Solar Controller Utility: Run the program

User’s Manual of BSP-30023

Toolbar on the top: Item Action Open Open the existing controller parameter file in the computer. Save Convert the controller parameters into a fil

 User’s Manual of BSP-30025the load. It requires the charging from the PV panel so as to increase the battery voltag

 User’s Manual of BSP-30026Pulse Width Modulation (PWM) Control: When this function is enabled, the brightness of th

 User’s Manual of BSP-30027Appendix A: Glossary (LVD) Low Voltage Disconnection When the battery voltage is less th

 User’s Manual of BSP-30028 In this controller, the pulse‐width modulation is mainly achieved by using the MOS trans

User’s Manual of BSP-3002Safety This device is designed with the utmost care for the safety of those who install and

 User’s Manual of BSP-30029acceleration power. Please do not use this type of battery unless you have no other types

 User’s Manual of BSP-30030to contact your battery manufacturers for correct usage suggestions. This product mainly

 User’s Manual of BSP-30031Appendix B: Recommended Use of the Connection Wires (Applicable to the system with volta

 User’s Manual of BSP-30032Appendix C: Recommended Settings for Different Batteries Description Specification Batte

User’s Manual of BSP-30033Appendix D: Troubleshooting Problem Inspection Procedure For the initial installation, al

User’s Manual of BSP-30034the solar controller. If the current exceed the rated current of the solar controller, ple

 User’s Manual of BSP-3003Table of Contents CHAPTER 1. RENEWABLE ENERGY...

 User’s Manual of BSP-3004Chapter 1. Renewable Energy “Renewable energy” means the energy of which the source never

 User’s Manual of BSP-3005In physics, such an energy conversion process is called “photovoltaic” (PV) (photo = light

 User’s Manual of BSP-3006proper ventilation. ￭ While connecting the PV panels or the batteries to the controll

 User’s Manual of BSP-3007Chapter 2. Introduction Industry-leading integration of PoE technology and Solar Power Sys

 User’s Manual of BSP-3008Application Site  Forest / National Park Monitoring  Public Surveillance / Public Wire