Command Guide of MGSW-28240F -1-
Command Guide of MGSW-28240F 4.2.69 ip igmp host-proxy ...
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping max-grou
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp 4.2.56.41 lacp ke
Command Guide of MGSW-28240F Example: To configure LACP port-priority (555) for GigabitEthernet X/X Switch# configure terminal Switch (config)# inte
Command Guide of MGSW-28240F Default: Fast Usage Guide: To configure LACP timeout type for specific interface Example: To enable LACP timeout ty
Command Guide of MGSW-28240F media-vlan Media VLAN assignment policy-list Assignment of policies <v_range_list> Policies to assign t
Command Guide of MGSW-28240F 4.2.56.48 lldp receive Command: lldp receive lldp LLDP configurations receive Enable/Disable decoding o
Command Guide of MGSW-28240F 4.2.56.50 lldp tlv-select port-description Command: lldp tlv-select port-description lldp LLDP configurations
Command Guide of MGSW-28240F Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select system-capabilities 4.2.56.52 lldp tl
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select system-n
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect 4.2.56.56
Command Guide of MGSW-28240F 4.2.94.9 length ...
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect tx-mode
Command Guide of MGSW-28240F To enable learning of MAC address table for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface
Command Guide of MGSW-28240F To configure MTU sizes for specific interface Example: To configure MTU sizes (9000) for GigabitEthernet X/X Switch# co
Command Guide of MGSW-28240F Default: Inactive Usage Guide: To configure port role of specific MVR profile for specific interface Example: To co
Command Guide of MGSW-28240F network-clock synchronization ssm network-clock network-clock synchronization SSM enable/disable. ssm SSM enabl
Command Guide of MGSW-28240F ping ip <ipv4_addr> size <size: 2-1452> ping The ping command allows you to test connectivity to a n
Command Guide of MGSW-28240F 4.2.56.69 poe pdcheck IP Command: poe pdcheck IP <ipv4_addr> poe Power Over Ethernet. pdcheck
Command Guide of MGSW-28240F Example: To configure PD Ping Alive Check Action (Alarm) of PoE for GigabitEthernet X/X. Switch# configure terminal S
Command Guide of MGSW-28240F Default: 30 Usage Guide: To configure PD Ping Alive Check interval of PoE for specific interface. Example: To confi
Command Guide of MGSW-28240F pdcheck Allows user to enable or disable per port PD Alive Check function. retry-count set how many times sy
Command Guide of MGSW-28240F 4.2.130 mep <Instance> meg-id...
Command Guide of MGSW-28240F Command: poe priority { low | high | critical } poe Power Over Ethernet. priority Interface priority.
Command Guide of MGSW-28240F Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe time-range profile3 4.2.56.78 port-security Com
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # port-security maximum 10
Command Guide of MGSW-28240F Default: None (Protected) Usage Guide: To configure protected mode of Port-security for specific interface Example:
Command Guide of MGSW-28240F Default: None Usage Guide: To enable PVLAN isolation for specific interface Example: To enable PVLAN isolation for
Command Guide of MGSW-28240F Default: 0 Usage Guide: To configure DEI of QoS for specific interface Example: To configure DEI (1) of QoS for Gi
Command Guide of MGSW-28240F dscp-classify DSCP ingress classification any Classify to new DSCP always selected Classify to new DSCP if
Command Guide of MGSW-28240F 4.2.56.89 qos dscp-translate Command: qos dscp-translate qos Quality of Service dscp-translate DSCP ingr
Command Guide of MGSW-28240F To configure (QoS class, DP level) to (PCP, DEI) Mapping of QoS for specific interface Example: To configure (QoS class
Command Guide of MGSW-28240F Switch (config-if) # qos map tag-cos pcp 4 dei 0 cos 5 dpl 1 4.2.56.92 qos pcp Command: qos pcp <Pcp : 0-7> qo
Command Guide of MGSW-28240F 4.2.167.4 no ...
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos policer 9999 4.2.5
Command Guide of MGSW-28240F 0 Usage Guide: To configure Egress Queue Shapers Rate of QoS for specific interface Example: To configure Egress Queu
Command Guide of MGSW-28240F qos Quality of Service storm Storm policer broadcast Police broadcast frames <Rate : 100-13200000&
Command Guide of MGSW-28240F 4.2.56.99 qos storm unknown Command: qos storm unknown <Rate : 100-13200000> [fps] qos Quality of Servi
Command Guide of MGSW-28240F Example: To enable Tag-remark default mode (PCP:1 , DEI:1) of QoS for GigabitEthernet X/X Switch# configure terminal
Command Guide of MGSW-28240F Usage Guide: To enable DSCP Classification of QoS for specific interface Example: To enable DSCP Classification of QoS
Command Guide of MGSW-28240F history Configure history buckets Requested buckets of intervals. Default is 50 buckets interval Interval to s
Command Guide of MGSW-28240F Switch (config-if) # rmon collection stats 2 4.2.56.106 shutdown Command: shutdown shutdown Shutdown of the inter
Command Guide of MGSW-28240F 4.2.56.108 spanning-tree auto-edge Command: spanning-tree auto-edge spanning-tree Spanning Tree protocol auto-edg
Command Guide of MGSW-28240F 4.2.56.110 spanning-tree edge Command: spanning-tree edge spanning-tree Spanning Tree protocol edge
Command Guide of MGSW-28240F 4.2.197.9 version...
Command Guide of MGSW-28240F Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree edge 4.2.56.112 spanning-tree mst <
Command Guide of MGSW-28240F auto Use auto cost Default: Auto Usage Guide: To configure Path Cost of CIST / MST Normal Port Configu
Command Guide of MGSW-28240F Command: spanning-tree restricted-tcn spanning-tree Spanning Tree protocol restricted-tcn Restrict topology chan
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # speed 1000 4.2.56.117
Command Guide of MGSW-28240F Default: 1 Usage Guide: To add forbidden VLAN ID for specific interface Example: To add forbidden VLAN ID (5) for
Command Guide of MGSW-28240F 4.2.56.120 switchport hybrid acceptable-frame-type Command: switchport hybrid acceptable-frame-type all | tagged | untag
Command Guide of MGSW-28240F Default: All Usage Guide: To configure VLAN list of Hybrid VLAN for specific interface Example: To configure VLA
Command Guide of MGSW-28240F 4.2.56.123 switchport hybrid ingress-filtering Command: switchport hybrid ingress-filtering switchport Switching mode
Command Guide of MGSW-28240F Example: To enable PVID (5) in Hybrid VLAN mode for GigabitEthernet X/X Switch# configure terminal Switch (config)#
Command Guide of MGSW-28240F switchport mode c-port | s-custom-port | s-port | unaware switchport Switching mode characteristics mode Set m
Command Guide of MGSW-28240F 4.4 debug...
Command Guide of MGSW-28240F Usage Guide: To configure IP Subnet-based VLAN for specific interface Example: To configure IP Subnet-based VLAN as b
Command Guide of MGSW-28240F Switch (config-if) # switchport vlan mac 00:55:44:33:22:11 vlan 5 4.2.56.129 switchport vlan mapping Command: switchpo
Command Guide of MGSW-28240F None Usage Guide: To configure VLAN protocol group for specific interface Example: To configure VLAN protocol group
Command Guide of MGSW-28240F 4.2.56.132 switchport voice vlan mode Command: switchport voice vlan mode auto | disable | force switchport Switchi
Command Guide of MGSW-28240F Default: Disabled Usage Guide: To enable Voice VLAN security for specific interface Example: To enable Voice VL
Command Guide of MGSW-28240F 4.2.57.1 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage G
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# end Switch# 4.2.57.3 exit Command
Command Guide of MGSW-28240F Usage Guide: To configure IP address mode for specific VLAN Example: To configure IP address mode (192.168.1.10/24)
Command Guide of MGSW-28240F ip Interface Internet Protocol config commands address Address configuraton dhcp Enable DHCP &l
Command Guide of MGSW-28240F 4.2.57.8 ip igmp snooping Command: ip igmp snooping ip Interface Internet Protocol config commands igmp
Command Guide of MGSW-28240F 4.19.2 reload defaults...
Command Guide of MGSW-28240F Auto Usage Guide: To configure IGMP snooping version for specific VLAN Example: To configure IGMP snooping V2 for VL
Command Guide of MGSW-28240F Command: ip igmp snooping priority <CosPriority : 0-7> ip Interface Internet Protocol c
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping querier address 1
Command Guide of MGSW-28240F query-interval Query Interval in seconds <IpmcQi : 1-31744> 1 - 31744 seconds Default: 125 Usage Guid
Command Guide of MGSW-28240F 4.2.57.16 ip igmp snooping robustness-variable Command: ip igmp snooping robustness-variable <IpmcRv : 1-255>
Command Guide of MGSW-28240F Example: To configure Unsolicited-Report-Interval (99 seconds) of IGMP snooping for VLAN X Switch# configure terminal S
Command Guide of MGSW-28240F Default: Disabled Usage Guide: To enable MLD snooping for specific VLAN Example: To enable MLD snooping for VLAN
Command Guide of MGSW-28240F 4.2.57.21 ipv6 mld snooping last-member-query-interval Command: ipv6 mld snooping last-member-query-interval <IpmcLm
Command Guide of MGSW-28240F Usage Guide: To configure CoS priority of MLD snooping for specific VLAN Example: To configure CoS priority (5) of ML
Command Guide of MGSW-28240F mld Multicast Listener Discovery snooping Snooping MLD query-interval Query Interval in seconds &l
Command Guide of MGSW-28240F 4.21.37 show ip dhcp server declined-ip (GG) ...
Command Guide of MGSW-28240F Switch (config-if-vlan)# ipv6 mld snooping query-max-response-time 600 4.2.57.26 ipv6 mld snooping robustness-variable
Command Guide of MGSW-28240F 1 Usage Guide: To configure Unsolicited-Report-Interval of MLD snooping for specific VLAN Example: To configure Unso
Command Guide of MGSW-28240F arp Address Resolution Protocol inspection ARP inspection Default: N/A Usage Guide: To enable ARP i
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# ip arp inspection entry interface GigabitEthernet 1/1 1 00:11:22:33:44:55 1
Command Guide of MGSW-28240F ip Internet Protocol arp Address Resolution Protocol inspection ARP inspection translate
Command Guide of MGSW-28240F Default: N/A Usage Guide: To configure VLAN mode of ARP inspection. Example: To configure VLAN mode (VLAN 1, Log
Command Guide of MGSW-28240F ip dhcp pool <WORD> ip Internet Protocol dhcp Dynamic Host Configuration Protocol pool
Command Guide of MGSW-28240F 4.2.64.2 client-identifier fqdn Command: client-identifier fqdn <LINE> client-identifier Client identifier f
Command Guide of MGSW-28240F To configure Bind IP to MAC (00:11:22:33:44:55) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Sw
Command Guide of MGSW-28240F Example: To configure Default Gateway (192.168.0.1) of DHCP Server for pool “planetbestswitch” Switch# configure termin
Command Guide of MGSW-28240F 4.21.78 show port-security switch ...
Command Guide of MGSW-28240F Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# ip dhcp po
Command Guide of MGSW-28240F Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To b
Command Guide of MGSW-28240F 4.2.64.11 hardware-address Command: hardware-address <MAC> hardware-address Client hardware address <
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# host 192.168.1.10 2
Command Guide of MGSW-28240F Usage Guide: To configure NetBIOS Name Server of DHCP Server. Example: To configure NetBIOS Name Server (192.168.1.10
Command Guide of MGSW-28240F netbios-scope NetBIOS scope <LINE> Netbios scope identifier, in 128 characters Default: None Usage Guide
Command Guide of MGSW-28240F 4.2.64.18 nis-domain-name Command: nis-domain-name <word128> nis-domain-name NIS domain name <word128&g
Command Guide of MGSW-28240F Switch (config-dhcp-pool)# nis-server 1.1.1.1 4.2.64.20 no Command: no no Negate a command or set its defaults
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# ntp-server 1.1.1.1
Command Guide of MGSW-28240F Default: Disabled Usage Guide: To enable DNS proxy. Example: To enable DNS proxy. Switch# configure terminal Sw
Command Guide of MGSW-28240F 4.22.3 terminal history size...
Command Guide of MGSW-28240F ip Internet Protocol http Hypertext Transfer Protocol secure-redirect Secure HTTP web redirect
Command Guide of MGSW-28240F 4.2.69 ip igmp host-proxy Command: ip igmp host-proxy ip Internet Protocol igmp Internet Group Ma
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# ip igmp host-proxy leave-proxy 4.2.71 ip igmp snooping Command: ip igmp sn
Command Guide of MGSW-28240F Usage Guide: To enable IGMP Snooping for specific VLAN. Example: To enable IGMP Snooping for VLAN 1. Switch# configur
Command Guide of MGSW-28240F unknown-flooding Flooding unregistered IPv4 multicast traffic Default: Enabled Usage Guide: To flood unregister
Command Guide of MGSW-28240F ip name-server dhcp ip Internet Protocol name-server Domain Name System dhcp Dynamic Host Confi
Command Guide of MGSW-28240F 4.2.78 ip route Command: ip route <ipv4_addr> <ipv4_netmask> <ipv4_gateway> ip Internet P
Command Guide of MGSW-28240F Usage Guide: To enable IP routing Example: To enable IP routing Switch# configure terminal Switch (config)# ip ro
Command Guide of MGSW-28240F 4.2.81 ip ssh Command: ip ssh ip Internet Protocol ssh Secure Shell Default: None Usage Guide: To enab
Command Guide of MGSW-28240F To enable IP Source Guard Switch# configure terminal Switch (config)# ip verify source 4.2.83 ip verify source transla
Command Guide of MGSW-28240F Contents Chapter 1 COMMAND LINE INTERFACE... 20 1.1 Accessing the
Command Guide of MGSW-28240F Chapter 1 COMMAND LINE INTERFACE 1.1 Accessing the CLI When accessing the management interface for the switch over a d
Command Guide of MGSW-28240F Usage Guide: To enable IPMC profile Example: To enable IPMC profile Switch# configure terminal Switch (config)# ip
Command Guide of MGSW-28240F <EntryName : word16> Range entry name Default: None Usage Guide: To default IPMC Profile Rule for spec
Command Guide of MGSW-28240F Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To r
Command Guide of MGSW-28240F Switch (config-ipmc-profile)#end Switch# 4.2.85.5 exit Command: exit exit Exit from current mode D
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# no description 999 4.2
Command Guide of MGSW-28240F Disabled Usage Guide: To enable MLD Proxy Example: To enable MLD Proxy. Switch# configure terminal Switch (config)#
Command Guide of MGSW-28240F mld Multicast Listener Discovery snooping Snooping MLD Default: Disabled Usage Guide: To enable ML
Command Guide of MGSW-28240F Command: ipv6 mld ssm-range <ipv6_mcast> <Ipv6PrefixLength : 8-128> ipv6 IPv6 configuration command
Command Guide of MGSW-28240F 4.2.92 ipv6 route Command: Ipv6 route <X:X:X:X::X/<0-128>> {<X:X:X:X::X>, interface vlan <vlan_id
Command Guide of MGSW-28240F 4.2.93 lacp system-priority Command: lacp system-priority <1-65535> lacp LACP settings system-priority
Command Guide of MGSW-28240F The CLI provides the following modes: User Mode When the operator logs into the CLI, the User Mode is the initial
Command Guide of MGSW-28240F To enter line mode (vty 1) Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# 4.2.94.1 do Co
Command Guide of MGSW-28240F Enabled Usage Guide: To allow user editing command line. Example: To allow user editing command line. Switch# confi
Command Guide of MGSW-28240F exec-banner Enable the display of the EXEC banner Default: Enabled Usage Guide: To enable the display
Command Guide of MGSW-28240F 4.2.94.6 exec-timeout Command: exec-timeout <0-1440> exec-timeout Set the EXEC timeout <0-1440>
Command Guide of MGSW-28240F Switch (config-line)# exit Switch (config)# 4.2.94.8 history size Command: history size <0-32> history
Command Guide of MGSW-28240F To configure displayed lines on a screen. Example: To configure displayed lines on a screen. Switch# configure termina
Command Guide of MGSW-28240F Enabled Usage Guide: To enable MOTD banner. Example: To enable MOTD banner.. Switch# configure terminal Switch (con
Command Guide of MGSW-28240F level Assign default privilege level for line <0-15> Default privilege level for line Default:
Command Guide of MGSW-28240F 4.2.95 lldp holdtime Command: lldp holdtime <2-10> lldp LLDP configurations. holdtime Sets LLDP ho
Command Guide of MGSW-28240F To configure Datum type of LLDP Example: To configure Datum type (nad83-mllw) of LLDP Switch# configure terminal Swi
Command Guide of MGSW-28240F Chapter 2 CONSOLE CLI MANAGEMENT 2.1 Terminal Setup To configure the system, connect a serial cable to a COM port on a PC
Command Guide of MGSW-28240F floors Specify the altitude in floor. <Meters or floors> Altitude value. meters Specify the altitude i
Command Guide of MGSW-28240F 4.2.100 lldp med location-tlv latitude Command: lldp med location-tlv latitude north <Degrees> | south <Degre
Command Guide of MGSW-28240F Default: North, 0 Usage Guide: To configure longitude direction of LLDP-MED Example: To configure longitude di
Command Guide of MGSW-28240F Default: 0 Usage Guide: To configure media-VLAN-policy of LLDP-MED Example: To configure media-VLAN-policy as b
Command Guide of MGSW-28240F Command: lldp timer <5-32768> lldp LLDP configurations. timer Sets LLDP TX interval (The tim
Command Guide of MGSW-28240F 4.2.106 logging host Command: logging host <hostname> | <ipv4_ucast> logging Syslog host host
Command Guide of MGSW-28240F Example: To configure level of log server Switch# configure terminal Switch (config)# logging level error 4.2.108 l
Command Guide of MGSW-28240F Usage Guide: To enable Loop Protection Example: To enable Loop Protection Switch# configure terminal Switch (confi
Command Guide of MGSW-28240F Default: 5 Usage Guide: To configure Transmission Time of Loop Protection Example: To configure Transmission Ti
Command Guide of MGSW-28240F <port_type_list> | GigabitEthernet <port_type_list> mac MAC table entries/configuration address-tab
Command Guide of MGSW-28240F Figure 2-3 Hyper Terminal COM Port Configuration You can change these settings, if desired, after you log on. This mana
Command Guide of MGSW-28240F Default: None Usage Guide: To configure AIS of MEP Example: To configure AIS of MEP 1 as below table Switch
Command Guide of MGSW-28240F To configure APS of MEP 1 as below table Switch# configure terminal Switch (config)# mep 1 aps 7 laps 4.2.116 mep <
Command Guide of MGSW-28240F 4.2.117 mep <Instance> client domain Command: mep <Instance> client domain { evc | vlan } mep Mai
Command Guide of MGSW-28240F <Lckprio : 0-7> LCK injection priority value. lck-highest Request the highest possible LCK priority.
Command Guide of MGSW-28240F uni OAM PDU is transmitted with unicast MAC. The MAC is taken from peer MEP MAC database. mep-id Peer
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# mep 1 dm ns 4.2.121 mep <Instance> dm overflow-reset Command: mep
Command Guide of MGSW-28240F proprietary Proprietary Delay Measurement Default: Standard Usage Guide: To configure Tx mode (proprietary)
Command Guide of MGSW-28240F Command: mep <Instance> [ mip ] down domain { port | evc | vlan } [ vid <vid> ] flow <flow> level <
Command Guide of MGSW-28240F lb Loop Back <Prio : 0-7> Priority in case of tagged OAM. In the EVC domain this is the COS-ID. cou
Command Guide of MGSW-28240F mep <Instance> lck fr1m | fr1s mep Maintenance Entity Point <Instance> The MEP instance number. l
Command Guide of MGSW-28240F 2.2 Logon to the Console Once the terminal is connected to the device, power on the Managed Switch, and the terminal will
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# mep 2 level 2 4.2.128 mep <Instance> lm Command: mep <Instance&g
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# mep 2 lm 5 uni flr 4 4.2.129 mep <Instance> lt Command: mep <Ins
Command Guide of MGSW-28240F mep <Instance> meg-id <megid> { itu | itu-cc | { ieee [ name <name> ] } } mep Maintenance Entit
Command Guide of MGSW-28240F Default: None Usage Guide: To configure MEP-ID of MEP. Example: To configure MEP-ID (5) of MEP 1. Switch# confi
Command Guide of MGSW-28240F 4.2.133 mep <Instance> performance-monitoring Command: mep <Instance> performance-monitoring mep
Command Guide of MGSW-28240F one-zero Test pattern is set to 10101010. rate The TST frame transmission bit rate - in Mega bits p
Command Guide of MGSW-28240F <flow > The flow instance number when not in the port domain. vid In case the MEP is a port Up-MEP or
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# mep 1 vid 8 4.2.137 mep <Instance> voe Command: mep <Instance>
Command Guide of MGSW-28240F Example: To set Mirroring Port (GigabitEthernet 1/2) Switch# configure terminal Switch (config)# monitor destination
Command Guide of MGSW-28240F Example: To enable MVR Switch# configure terminal Switch (config)# mvr 4.2.141 mvr name <mvr_name> channel Com
Command Guide of MGSW-28240F Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the curre
Command Guide of MGSW-28240F frame MVR control frame in TX priority Interface CoS priority <CosPriority : 0-7> CoS priority ranges from
Command Guide of MGSW-28240F 4.2.144 mvr name <mvr_name> igmp-address Command: mvr name <mvr_name> igmp-address <ipv4_ucast> mvr
Command Guide of MGSW-28240F To configure the Last Member Query Interval of MVR profile Example: To configure the Last Member Query Interval (50 s
Command Guide of MGSW-28240F <vlan_list> MVR multicast VLAN list Default: None Usage Guide: To create a profile of MVR VLAN Exa
Command Guide of MGSW-28240F 4.2.149 mvr vlan <vlan_list> frame priority Command: mvr vlan <vlan_list> frame priority <CosPriority : 0
Command Guide of MGSW-28240F To enable the IGMP/MLD frame tagged of MVR VLAN (123) Switch# configure terminal Switch (config)# mvr vlan 123 tagged
Command Guide of MGSW-28240F <IpmcLmqi : 0-31744> 0 - 31744 tenths of seconds Default: 5 Usage Guide: To configure the Last Member
Command Guide of MGSW-28240F 4.2.154 mvr vlan <vlan_list> name Command: mvr vlan <vlan_list> name mvr Multicast VLAN Registration
Command Guide of MGSW-28240F Example: To configure preferred negotiation (slave) of network-clock (source 1) Switch# configure terminal Switch (con
Command Guide of MGSW-28240F nominate Nominate a clk input to become a selectable clock source. clk-in Nominate the station clock
Command Guide of MGSW-28240F 4. Repeat step 1 to check if the IP address is changed. Store current switch configuration 5. At the “#” prompt, ent
Command Guide of MGSW-28240F 4.2.159 network-clock clk-source <clk-source> ssm-overwrite Command: network-clock clk-source <clk-source>
Command Guide of MGSW-28240F Default: None Usage Guide: To configure EEC options of network-clock Example: To configure EEC options (eec1) o
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# network-clock selector freerun 4.2.162 network-clock ssm-freerun Command:
Command Guide of MGSW-28240F eec1 eec1 eec2 eec2 inv inv prc prc ssua ssua ssub ssub Default: None Us
Command Guide of MGSW-28240F Switch (config)# network-clock wait-to-restore 6 4.2.165 no Command: no no Negate a command or set its defaults D
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# ntp 4.2.167 ntp server Command: ntp server <1-5> ip-address { <
Command Guide of MGSW-28240F Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# poe-time
Command Guide of MGSW-28240F Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example:
Command Guide of MGSW-28240F 4.2.167.5 periodic Command: periodic { Mon | Tue | Wed | Thu | Fri | Sat | Sun } <start_h> <start_m> to <
Command Guide of MGSW-28240F 4.2.167.6 reboot-only Command: reboot-only { Mon | Tue | Wed | Thu | Fri | Sat | Sun } <reboot_h> <reboot_m>
Command Guide of MGSW-28240F Chapter 3 TELNET CLI MANAGEMENT 3.1 Telnet Login The Managed Switch also supports telnet for remote management. The switc
Command Guide of MGSW-28240F Usage Guide: To enable the Port Security Example: To enable the Port Security Switch# configure terminal Switch
Command Guide of MGSW-28240F <10-10000000> seconds Default: 3600 Usage Guide: To configure the Aging Period of Port Security Example
Command Guide of MGSW-28240F Example: To configure the Privilege Level (DHCP Pool mode, Level 12, Command: host) for Command Line Switch# configure
Command Guide of MGSW-28240F ef Expedited Forwarding PHB(DSCP 46) va Voice Admit PHB(DSCP 44) Default: 0 Usage Guide: To con
Command Guide of MGSW-28240F cs3 Class Selector PHB CS3 precedence 3(DSCP 24) cs4 Class Selector PHB CS4 precedence 4(DSCP 32) cs5
Command Guide of MGSW-28240F af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assured Forwarding PHB AF42(DSCP 36) af43 Assur
Command Guide of MGSW-28240F dscp-egress-translation Map for dscp egress translation <DscpNum : 0-63> Specific DSCP af11 Ass
Command Guide of MGSW-28240F Command: qos map dscp-ingress-translation { <dscp_num> | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | a
Command Guide of MGSW-28240F Switch (config)# qos map dscp-ingress-translation af11 to af12 4.2.177 qos qce Command: qos qce <qce_id> [ { n
Command Guide of MGSW-28240F To configure the QCE Example: To configure the QCE 1 (below table) for interface GigabitEthernet 1/1-2 Switch# config
Command Guide of MGSW-28240F Chapter 4 Commands for CLI Configuration 4.1 clear 4.1.1 clear access management statistics Command: clear access manag
Command Guide of MGSW-28240F udp | any } ] [ sip { <sip6> | any } ] [ dip { <dip6> | any } ] [ dscp { <dscp6> | { be | af11 | af12 |
Command Guide of MGSW-28240F refresh Refresh QCE tables in hardware Default: None Usage Guide: To refresh the QCE Example: To refresh
Command Guide of MGSW-28240F Usage Guide: To configure the Weighted Random Early Detection Example: To configure the Weighted Random Early Detec
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# radius-server attribute 32 planet 4.2.182 radius-server attribute 4 Comm
Command Guide of MGSW-28240F Example: To configure the NAS-IPv6-Address (2001::7788) Switch# configure terminal Switch (config)# radius-server at
Command Guide of MGSW-28240F <AcctPort : 0-65535> UDP port number auth-port UDP port for RADIUS authentication server <Aut
Command Guide of MGSW-28240F To configure the Key (123456789) of Radius-Server Switch# configure terminal Switch (config)# radius radius-server ke
Command Guide of MGSW-28240F Usage Guide: To configure the timeout of Radius-Server Example: To configure the timeout (10) of Radius-Server Sw
Command Guide of MGSW-28240F ifOutNUcastPkts The number of broad-cast and multi-cast packets that request to transmi
Command Guide of MGSW-28240F <description> Event description log Generate RMON log when the event fires trap Generat
Command Guide of MGSW-28240F 4.1.3 clear dot1x statistics interface Command: clear dot1x statistics interface GigabitEthernet | 10GigabitEthernet
Command Guide of MGSW-28240F 4.2.192 snmp-server Command: snmp-server snmp-server Set SNMP server's configurations Default: Enabled
Command Guide of MGSW-28240F <ViewName : word255> read view name write specify a write view for the group <WriteName : word
Command Guide of MGSW-28240F To configure the Read / Write / Source network Community of SNMP Example: To configure the Read / Write / Source networ
Command Guide of MGSW-28240F snmp-server Set SNMP server's configurations engine-id Set SNMP engine ID local Set SNMP local
Command Guide of MGSW-28240F Switch (config)# snmp-server host planet Switch (config-snmps-host)# 4.2.197.1 do Command: do < exec commands >
Command Guide of MGSW-28240F Example: To back to EXEC mode Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snm
Command Guide of MGSW-28240F <ipv6_ucast> IP address of SNMP trap host <UdpPort : 1-65535> UDP port of the trap messages
Command Guide of MGSW-28240F Switch (config)# snmp-server host planet Switch (config-snmps-host)# no ip address dhcp 4.2.197.6 informs Command: in
Command Guide of MGSW-28240F Disabled Usage Guide: To disable Trap mode of SNMP Example: To disable Trap mode of SNMP Switch# configure terminal
Command Guide of MGSW-28240F 4.2.197.9 version Command: version { v1 [ <v1_comm> ] | v2 [ <v2_comm> ] | v3 [ probe | engineID <v_w
Command Guide of MGSW-28240F 4.1.20 clear ip statistics icmp icmp-msg ...
Command Guide of MGSW-28240F Switch# # clear erps 1 statistics 4.1.6 clear erps statistics Command: clear erps statistics Default: N/A Usage Gui
Command Guide of MGSW-28240F spanning-tree aggregation spanning-tree Spanning Tree protocol aggregation Aggregation mode Default:
Command Guide of MGSW-28240F http : local 4.2.198.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To b
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)#exit Switch (config)#
Command Guide of MGSW-28240F Enabled Usage Guide: To enable the Auto Edge of CIST Aggregated Port Example: To enable the Auto Edge of CIST Aggreg
Command Guide of MGSW-28240F edge Edge port Default: Disabled Usage Guide: To enable the Admin Edge of CIST Aggregated Port Example: To
Command Guide of MGSW-28240F 4.2.198.9 spanning-tree mst <instance> cost Command: spanning-tree mst <instance> cost { <cos
Command Guide of MGSW-28240F To configure the Port Priority of MSTI Port Example: To configure the Port Priority (96) of MSTI Port (MST 2) Switch#
Command Guide of MGSW-28240F Default: Disabled Usage Guide: To enable the Restricted TCN of CIST Example: To enable the Restricted TCN of CIST
Command Guide of MGSW-28240F 4.2.200 tacacs-server deadtime Command: tacacs-server deadtime <minutes> tacacs-server Configure TAC
Command Guide of MGSW-28240F Default: None Usage Guide: To configure the Host of TACACS+ Server Example: To enable the Host (below table) of T
Command Guide of MGSW-28240F 4.1.8 clear ip dhcp detailed statistics all Command: clear ip dhcp detailed statistics all Default: N/A Usage Guide:
Command Guide of MGSW-28240F 4.2.203 transport email from Command: transport email from <mail_addr> subject <title> transport
Command Guide of MGSW-28240F Usage Guide: To configure SMTP Server address and port number. Example: To configure SMTP Server address (mail.plan
Command Guide of MGSW-28240F Command: upnp upnp Set UPnP's configurations Default: Disabled Usage Guide: To enable the UPnP servic
Command Guide of MGSW-28240F 4.2.208 upnp ttl Command: upnp ttl <1-255> upnp Set UPnP's configurations ttl Set TTL va
Command Guide of MGSW-28240F None Usage Guide: To configure the Profiles of Username Example: To configure the Profiles of Username (Username: 12
Command Guide of MGSW-28240F 4.2.210.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)#end Switch# 4.2.210.3 exit Command: exit
Command Guide of MGSW-28240F To configure description of VLAN Example: To configure description (FAE) of VLAN Switch# configure terminal Switch (
Command Guide of MGSW-28240F Default: 0x88A8 Usage Guide: To create the Ethernet type of Custom S-ports Example: To create the Ethernet type
Command Guide of MGSW-28240F Usage Guide: To configure the Protocol-based VLAN Example: To configure the Protocol-based VLAN (below table) Swit
Command Guide of MGSW-28240F Default: N/A Usage Guide: To clear the DHCP normal L2 or L3 forward statistics. Example: To clear the Switch’s DHCP n
Command Guide of MGSW-28240F aging-time Set secure learning aging time <AgingTime : 10-10000000> Aging time, 10-10000000 seconds
Command Guide of MGSW-28240F 4.2.216 voice vlan oui Command: voice vlan oui <oui> [ description <description> ] voice Voice applian
Command Guide of MGSW-28240F Example: To configure the VID (66 ) of Voice VLAN Switch# configure terminal Switch (config)# voice vlan vid 66
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# web privilege group Aggregation level cro 3 crw 4 sro 3 srw 5 4.3 cop
Command Guide of MGSW-28240F Command: debug prompt <debug_prompt> debug Debugging functions prompt Set prompt for testing &l
Command Guide of MGSW-28240F % Saving 1833 bytes to flash:222 Switch # dir Directory of flash: r- 1970-01-01 00:00:00 648 default-config
Command Guide of MGSW-28240F r- 1970-01-01 00:00:00 648 default-config rw 1970-01-01 07:26:26 1833 startup-config 2 files, 2481 bytes
Command Guide of MGSW-28240F Example: To run “show aaa”. Switch# do show aaa console : local telnet : local ssh : local http : local 4.9
Command Guide of MGSW-28240F Command: enable enable Turn on privileged commands Default: None Usage Guide: To enter enable mode Example
Command Guide of MGSW-28240F To configure Instance Command (below table) of Group (1) Switch # erps 1 command force port0 4.12 exit 4.12.1 exi
Command Guide of MGSW-28240F Switch# clear ip dhcp detailed statistics snooping 4.1.13 clear ip dhcp relay statistics Command: clear ip dhcp relay
Command Guide of MGSW-28240F Command: firmware swap firmware Firmware upgrade/swap swap Swap between Active and Alternate firmware
Command Guide of MGSW-28240F 4.14 ip 4.14.1 ip dhcp retry interface vlan Command: ip dhcp retry interface vlan <vlan_id> ip IPv4 c
Command Guide of MGSW-28240F Usage Guide: To exit EXEC mode Example: To exit EXEC mode Switch # logout Press ENTER to get started 4.16 more 4.
Command Guide of MGSW-28240F ! ! ! 4.17 no 4.17.1 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To
Command Guide of MGSW-28240F repeat Specify repeat count <Count : 1-60> 1-60; Default is 5 size Specify datagram size
Command Guide of MGSW-28240F Default: N/A Usage Guide: To run the IPv6 Ping function Example: To run the IPv6 Ping (2001::7788) function
Command Guide of MGSW-28240F 4.19.2 reload defaults Command: reload defaults [ keep-ip ] reload Reload system defaults Reload defaults wit
Command Guide of MGSW-28240F To send message for command line user. Example: To send message ( hi, I will upgrade the firmware, OK? ) for command
Command Guide of MGSW-28240F console : local telnet : local ssh : local http : local 4.21.2 show access management Command: show access
Command Guide of MGSW-28240F 4.21.3 show access-list Command: show access-list [ interface [ ( <port_type> [ <v_port_type_list> ] ) ]
Command Guide of MGSW-28240F Command: clear ip dhcp server binding automatic Default: N/A Usage Guide: To clear the DHCP automatic bindings cache
Command Guide of MGSW-28240F Switch access-list rate limiter ID 16 is 1 pps GigabitEthernet 1/1 : --------------------- GigabitEthernet 1/1 access-l
Command Guide of MGSW-28240F Switch access-list rate limiter ID 1 is 1 pps Switch access-list rate limiter ID 2 is 1 pps Switch access-list rate limi
Command Guide of MGSW-28240F conflicts The ACEs that did not get applied to the hardware due to hardware limitatio
Command Guide of MGSW-28240F 4.21.6 show aggregation Command: show aggregation [ mode ] show Show running system information aggregat
Command Guide of MGSW-28240F Example: To display the Aggregation mode status. Switch # show aggregation mode Aggregation Mode: SMAC : Enabled DM
Command Guide of MGSW-28240F show clock detail show Show running system information clock Configure time-of-day clock detail Disp
Command Guide of MGSW-28240F 4.21.10 show dot1x statistics Command: show dot1x statistics show Show running system information dot1x
Command Guide of MGSW-28240F Rx Auth. Successes: 0 Rx Auth. Failures: 0 4.21.11 show dot1x status Comman
Command Guide of MGSW-28240F Admin State Port State Last Source Last ID ------------------ ---------------------
Command Guide of MGSW-28240F Inst Dom Archi Wflow Pflow Wmep Pmep 1 Port 1plus1 1 2
Command Guide of MGSW-28240F Example: To clear the Switch’s DHCP server manual binding cache. Switch# clear ip dhcp server binding manual 4.1.18 c
Command Guide of MGSW-28240F Hold-Off Timeout :0 Guard Timeout :500 Node Type
Command Guide of MGSW-28240F EVC ID Status ------ ------ 1 Active 4.21.15 show evc statistics Command: show green-ethernet [ interface ( &
Command Guide of MGSW-28240F Default: N/A Usage Guide: To display the Green Ethernet status. Example: To display the Green Ethernet sta
Command Guide of MGSW-28240F show green-ethernet short-reach [ interface ( <port_type> [ <port_list> ] ) ] show Show running sys
Command Guide of MGSW-28240F show green-ethernet energy-detect show green-ethernet show green-ethernet short-reach interface * show history
Command Guide of MGSW-28240F interface Interface status and configuration statistics Display statistics counters bytes Sho
Command Guide of MGSW-28240F Example: To display the port status for interface GigabitEthernet 1/1. Switch # show interface GigabitEthernet 1/1 sta
Command Guide of MGSW-28240F Acceptable Frame Type: All Ingress filter: Disabled Egress tagging: All except-native Hybrid Native Mode VLAN: 1 Hybrid V
Command Guide of MGSW-28240F interface Interface status and configuration veriphy Run cable diagnostics and show result. Default:
Command Guide of MGSW-28240F Switch # show interface vlan VLAN1 LINK: 00-30-4F-00-99-00 Mtu:1500 <UP BROADCAST RUNNING MULTICAST> IPv4: 192
Command Guide of MGSW-28240F 4.1.20 clear ip statistics icmp icmp-msg Command: clear ip statistics icmp icmp-msg <Type : 0~255> <Type : 0~25
Command Guide of MGSW-28240F Default: N/A Usage Guide: To display the ARP Inspection Configuration. Example: To display the ARP Inspection
Command Guide of MGSW-28240F Switch # show ip arp inspection ARP Inspection Mode : disabled Port Port Mode Check VLAN Log Typ
Command Guide of MGSW-28240F show ip dhcp detailed statistics { server | client | snooping | relay | normal-forward | combined } [ interface ( <por
Command Guide of MGSW-28240F Rx Inform: 0 Tx Inform: 0 Rx Lease Query: 0
Command Guide of MGSW-28240F 4.21.33 show ip dhcp pool Command: show ip dhcp pool [ <pool_name> ] show Show running system information
Command Guide of MGSW-28240F Client name is - 4.21.34 show ip dhcp relay Command: show ip dhcp relay [ statistics ] show Show running sy
Command Guide of MGSW-28240F N/A Usage Guide: To display the DHCP Server Mode Configuration. Example: To display the DHCP Server Mode Configura
Command Guide of MGSW-28240F Example: To display the DHCP Server binding configuration. Switch # show ip dhcp server binding 4.21.37 show ip dhcp
Command Guide of MGSW-28240F Default: N/A Usage Guide: To display the DHCP Server statistics. Example: To display the DHCP Server stati
Command Guide of MGSW-28240F 4.21.39 show ip dhcp snooping Command: show ip dhcp snooping [interface ( <port_type> [ <port_list> ] )]
Command Guide of MGSW-28240F Default: N/A Usage Guide: To clear the IPv4 ICMP statistics for specific ICMP message type. Example: To clear the Swi
Command Guide of MGSW-28240F To display the DHCP Snooping table. Example: To display the DHCP Snooping table. Switch # show ip dhcp snooping tab
Command Guide of MGSW-28240F [ <port_type_list> ] ) ] [ sfm-information ] ] [ detail ] show Show running system information ip
Command Guide of MGSW-28240F Usage Guide: To display the IGMP Router Port information. Example: To display the IGMP Router Port information.
Command Guide of MGSW-28240F 4.21.45 show ip name-server Command: show ip name-server show Show running system information ip Inter
Command Guide of MGSW-28240F Switch # show ip route 11.11.11.0/24 via 192.168.0.14 <UP GATEWAY HW_RT> 127.0.0.1/32 via 127.0.0.1 <UP HOST>
Command Guide of MGSW-28240F Command: show ip ssh show Show running system information ip Internet Protocol ssh Secure Shel
Command Guide of MGSW-28240F IPv4 statistics: Rcvd: 9751 total in 1454882 bytes 9606 local destination, 0 forwarding 0 header er
Command Guide of MGSW-28240F Rcvd: 0 Packet Sent: 2618 Packets IPv4 ICMP Message: Echo Rcvd: 2618 Packets Sent: 0 Packet 4.21.50 show ip
Command Guide of MGSW-28240F ipmc IPv4/IPv6 multicast configuration profile IPMC profile configuration <ProfileName : word16>
Command Guide of MGSW-28240F Switch # show ipmc range Range Name : 1 Start Address: 224.24.24.24 End Address : 224.24.24.25 4.21.53 show ipv6
Command Guide of MGSW-28240F Switch# clear ipv6 mld snooping statistics 4.1.25 clear ipv6 mld snooping vlan Command: clear ipv6 mld snooping vlan &
Command Guide of MGSW-28240F 0 header error, 0 address error, 0 unknown protocol 0 no route, 0 truncated, 0 discarded Sent: 17 to
Command Guide of MGSW-28240F MLD Snooping is disabled to stop snooping MLD control plane. Multicast streams destined to unregistered MLD groups will b
Command Guide of MGSW-28240F vlan VLAN of IPv6 interface Default: N/A Usage Guide: To display the IPv6 neighbor information. Exam
Command Guide of MGSW-28240F 2001::7766/128 via 1:c100:9900:: <UP HOST> 2002::/64 via 2001::7788 <UP GATEWAY HW_RT> 4.21.58 show ipv6 st
Command Guide of MGSW-28240F Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fr
Command Guide of MGSW-28240F 4.21.59 show lacp Command: show lacp { internal | statistics | system-id | neighbour } show Show running syst
Command Guide of MGSW-28240F Usage Guide: To display the VTY information. Example: To display the VTY information. Switch # show line alive Li
Command Guide of MGSW-28240F Usage Guide: To display the Link OAM information. Example: To display the Link OAM statistics for GigabitEthernet
Command Guide of MGSW-28240F show lldp med media-vlan-policy [<0~31>] show Show running system information lldp Display LLDP nei
Command Guide of MGSW-28240F No LLDP-MED entries found 4.21.64 show lldp neighbors Command: show lldp neighbors [ interface ( <port_type> [
Command Guide of MGSW-28240F Command: clear ipv6 statistics icmp icmp-msg <Type : 0~255> <Type : 0~255> ICMP message type ranges from
Command Guide of MGSW-28240F Usage Guide: To display the LLDP statistics information. Example: To display the LLDP statistics information for Gi
Command Guide of MGSW-28240F ID : 235861 Level : Warning Time : 1970-01-01T13:33:57+00:00 Message: Loop Detected: Port 5 shut down 4.21.67
Command Guide of MGSW-28240F Transmit mode is enabled. No loop. The number of loops is 12390. Time of last loop is at 1970-01-01T1
Command Guide of MGSW-28240F Dynamic 1 d4:3d:7e:fd:e3:ac GigabitEthernet 1/21 Static 1 ff:ff:ff:ff:ff:ff GigabitEthernet 1/1-25 10GigabitEthe
Command Guide of MGSW-28240F 4.21.70 show mvr Command: show mvr [ vlan <vlan_list> | name <mvr_name> ] [ group-database [ interface (
Command Guide of MGSW-28240F Querier status is IDLE RX MLD Query:0 V1Report:0 V2Report:0 V1Done:0 TX MLD Query:0 / (Source) Specific Query:0 Interface
Command Guide of MGSW-28240F 4.21.72 show ntp status Command: show ntp status show Show running system information ntp Configure NT
Command Guide of MGSW-28240F interface Search by port Default: N/A Usage Guide: To display the PHY information. Example: To display
Command Guide of MGSW-28240F 4.21.75 show platform phy id Command: show platform phy id [ interface ( <port_type> [ <port_type_list> ]
Command Guide of MGSW-28240F Usage Guide: To display the PHY status. Example: To display the PHY status. Switch # show platform phy status in
Command Guide of MGSW-28240F 4.2.6 aaa authentication login http tacacs ...
Command Guide of MGSW-28240F N/A Usage Guide: To clear the IPv6 ICMP statistics for specific ICMP message type. Example: To clear the Switch’s IPv6
Command Guide of MGSW-28240F 4.21.78 show port-security switch Command: show port-security switch [ interface ( <port_type> [ <port_type_l
Command Guide of MGSW-28240F Usage Guide: To display the Privilege information. Example: To display the Privilege information. Switch # show p
Command Guide of MGSW-28240F Example: To display the PTP default information for PTP instance 0. Switch # show ptp 0 default ClockId DeviceType
Command Guide of MGSW-28240F 4.21.82 show ptp <clockinst> slave-cfg Command: show ptp <clockinst> slave-cfg show Show runnin
Command Guide of MGSW-28240F To display the unicast slave table. Example: To display the unicast slave table for PTP instance 0. Switch # show p
Command Guide of MGSW-28240F N/A Usage Guide: To display the Private VLAN membership configuration. Example: To display the Private VLAN member
Command Guide of MGSW-28240F 4.21.87 show qos Command: show qos [ { interface [ ( <port_type> [ <port> ] ) ] } | wred | { maps [ dscp-co
Command Guide of MGSW-28240F qos map tag-cos pcp 2 dei 0 cos 2 dpl 0 qos map tag-cos pcp 2 dei 1 cos 2 dpl 1 qos map tag-cos pcp 3 dei 0 cos 3 d
Command Guide of MGSW-28240F qos map cos-tag cos 4 dpl 0 pcp 4 dei 0 qos map cos-tag cos 4 dpl 1 pcp 4 dei 1 qos map cos-tag cos 5 dpl 0 pcp 5 d
Command Guide of MGSW-28240F Global RADIUS Server Attribute 4 : Global RADIUS Server Attribute 95 : Global RADIUS Server Attribute 32 : No hosts co
Command Guide of MGSW-28240F 4.1.32 clear lldp statistics Command: clear lldp statistics Default: N/A Usage Guide: To clear the lldp statisti
Command Guide of MGSW-28240F 4.21.90 show rmon event Command: show rmon event [ <id_list> ] show Show running system information r
Command Guide of MGSW-28240F Example: To display the RMON History ID 1 configuration. Switch # show rmon history 1 History ID : 1 ----------
Command Guide of MGSW-28240F etherStatsPkts : 127086 etherStatsBroadcastPkts : 45280 etherStatsMulticastPkts :
Command Guide of MGSW-28240F vlan VLAN line Show line settings console Console vty VTY Default: N/A Usage Guide:
Command Guide of MGSW-28240F 4.21.94 show snmp Command: show snmp show Show running system information snmp Display SNMP configurat
Command Guide of MGSW-28240F Privacy Protocol : None SNMPv3 Groups Table; Security Model : v1 Security Name : public Group Name : defaul
Command Guide of MGSW-28240F OID Subtree : .1 View Type : included 4.21.95 show snmp access Command: show snmp access [ <group_name> { v1
Command Guide of MGSW-28240F Security Model : any Security Level : NoAuth, NoPriv Read View Name : default_view Write View Name : default_vie
Command Guide of MGSW-28240F snmp Display SNMP configurations host Set SNMP host's configurations <ConfName : word32>
Command Guide of MGSW-28240F BRIDGE-MIB : - dot1dBase (.1.3.6.1.2.1.17.1) - dot1dTp (.1.3.6.1.2.1.17.4) Dot3-OAM-MIB : - dot3OamMIB (.1.3.
Command Guide of MGSW-28240F Default: N/A Usage Guide: To clear the logging error warning. Example: To clear the Switch’s logging error warning.
Command Guide of MGSW-28240F Q-BRIDGE-MIB : - qBridgeMIB (.1.3.6.1.2.1.17.7) RADIUS-ACC-CLIENT-MIB : - radiusAccClientMIBObjects (.1.3.6.1.2.1
Command Guide of MGSW-28240F mib MIB(Management Information Base) ifmib IF-MIB ifIndex The IfIndex that is defined in IF-MIB
Command Guide of MGSW-28240F 26 Switch 1 - Port 26 10GigabitEthernet 1/2 27 Switch 1 - Port 27
Command Guide of MGSW-28240F Security Name : public Group Name : default_ro_group Security Model : v2c Security Name : private Group Name :
Command Guide of MGSW-28240F 4.21.102 show snmp view Command: show snmp view [ <view_name> <oid_subtree> ] show Show running syst
Command Guide of MGSW-28240F summary STP summary mst Configuration configuration STP bridge instance no (0-7, CIST=0, MST1
Command Guide of MGSW-28240F Default: N/A Usage Guide: To display the VLAN Forbidden port entry. Example: To display the VLAN Forbidden port
Command Guide of MGSW-28240F Command: show terminal show Show running system information terminal Display terminal configuration
Command Guide of MGSW-28240F Default: N/A Usage Guide: To display the UPnP information. Example: To display the UPnP information. Switch # s
Command Guide of MGSW-28240F Line is vty 0. Connection is from 192.168.0.45:49527 by Telnet. User name is admin. Privilege is 15.
Command Guide of MGSW-28240F Switch# clear logging info warning 4.1.37 clear logging warning error Command: clear logging warning error Default
Command Guide of MGSW-28240F Alternate Image --------------- Image : managed.bk Version : 000 Date : 2013-10-02T15:1
Command Guide of MGSW-28240F 4.21.111 show vlan ip-subnet Command: show vlan ip-subnet [ id <subnet_id> ] show Show running system i
Command Guide of MGSW-28240F Example: To display the MAC-based VLAN information. Switch # show vlan mac MAC Address VID Interfaces --------
Command Guide of MGSW-28240F Switch # show vlan protocol Protocol Type Protocol (Value) Group ID ------------- ----------------------
Command Guide of MGSW-28240F GigabitEthernet 1/1 switchport voice discovery protocol is oui 4.21.115 show web privilege group Command: show
Command Guide of MGSW-28240F ETH_LINK_OAM 5 10 5 10 EVC 5 10 5 10 Green_Ethernet
Command Guide of MGSW-28240F terminal Set terminal line parameters editing Enable command line editing Default: Enabled Usage Guide:
Command Guide of MGSW-28240F Command: terminal history size <history_size> terminal Set terminal line parameters history Control
Command Guide of MGSW-28240F -438- -- more --, next page: Space, continue: g, quit: ^C 4.22.5 terminal width Command: terminal width <lines>
Command Guide of MGSW-28240F Command: clear mac address-table Default: N/A Usage Guide: To clear the mac address-table. Example: To clear the S
Command Guide of MGSW-28240F 4.1.42 clear mvr statistics Command: clear mvr statistics Default: N/A Usage Guide: To clear the mvr statistics. E
Command Guide of MGSW-28240F Default: N/A Usage Guide: To clear the ERPS WTR timer for a specific profile. Example: To clear the Switch’s ERPS WTR
Command Guide of MGSW-28240F Switch# clear spanning-tree detected-protocols interface * 4.1.47 clear spanning-tree detected-protocols interface G
Command Guide of MGSW-28240F To clear the Switch’s spanning-tree detected-protocols for specific 10GigabitEthernet 1/1. Switch# clear spanning-tree d
Command Guide of MGSW-28240F 4.1.51 clear spanning-tree statistics interface 10GigabitEthernet Command: clear spanning-tree statistics interface 10Gi
Command Guide of MGSW-28240F 4.2.47 erps <1-64> sub ...
Command Guide of MGSW-28240F Default: N/A Usage Guide: To clear the statistics for specific GigabitEthernet port. Example: To clear the Switch’s s
Command Guide of MGSW-28240F Example: To authenticate the local account via console. Switch# configure terminal Switch (config)# aaa authentication
Command Guide of MGSW-28240F 4.2.4 aaa authentication login http local Command: aaa authentication login http local Default: http : local Usage Gu
Command Guide of MGSW-28240F Default: http : local Usage Guide: To authenticate the tacacs account via http only. Example: To authenticate the lo
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# aaa authentication login ssh local radius 4.2.9 aaa authentication login s
Command Guide of MGSW-28240F 4.2.11 aaa authentication login telnet radius Command: aaa authentication login telnet radius Default: telnet : local
Command Guide of MGSW-28240F <AccessVid : 1-4095> The VLAN ID for the access management entry <AddrRangeStart : ipv4_addr> Start IPv
Command Guide of MGSW-28240F are limited. next Insert the current ACE before the next ACE ID policy Po
Command Guide of MGSW-28240F ingress Ingress logging Logging frame information. Note: The logging feature only
Command Guide of MGSW-28240F Usage Guide: To set pps rate for specific rate-limiter ID. Example: To set pps rate(10000 pps) for specific rate-limit
Command Guide of MGSW-28240F 4.2.56.32 ip igmp snooping max-groups ...
Command Guide of MGSW-28240F Default: SMAC : Enabled DMAC : Disabled IP : Enabled Port : Enabled Usage Guide: To configure static aggregatio
Command Guide of MGSW-28240F 4.2.20 banner Command: banner <LINE> <LINE> c banner-text c, where 'c' is a delimiting ch
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# banner exec 1 Enter TEXT message. End with the character '1'. gg
Command Guide of MGSW-28240F Password: 4.2.23 banner motd Command: banner motd <LINE> <LINE> c banner-text c, where 'c&a
Command Guide of MGSW-28240F <Timeend: hh:mm > <Offset minutes: 1-1440 > Default: N/A Usage Guide: To set daylight saving. Example: T
Command Guide of MGSW-28240F 0 Usage Guide: To default the Rate limiter. Example: To default the Rate limiter ID 1. Switch# configure terminal Swi
Command Guide of MGSW-28240F Switch (config)# dot1x authentication timer re-authenticate 777 4.2.29 dot1x feature Command: dot1x feature guest-vl
Command Guide of MGSW-28240F 4.2.31 dot1x guest-vlan supplicant Command: dot1x guest-vlan supplicant supplicant The switch remembers if an EAPOL
Command Guide of MGSW-28240F dot1x system-auth-control Default: Disable Usage Guide: To enable 802.1X service for Network Access Server Example:
Command Guide of MGSW-28240F To configure 802.1X EPOAL timeout for Network Access Server Example: To configure 802.1X EPOAL timeout (45 seconds) for
Command Guide of MGSW-28240F 4.2.56.73 poe pdcheck reboot-time...
Command Guide of MGSW-28240F <1-15> Level number <WORD> The UNENCRYPTED (cleartext) password. Default: Disable Usage Gui
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# enable secret 0 level 15 cisco # show running-config Building configuration.
Command Guide of MGSW-28240F <10-2000> Guard time in ms Default: 500 Usage Guide: To configure the Guard Time for ERPS. Example: To co
Command Guide of MGSW-28240F <1-64> ERPS group number interconnect Major ring is interconnected Default: 0 Usage Guide: To create a
Command Guide of MGSW-28240F 4.2.44 erps <1-64> mep Command: erps <1-64> revertive <wtr_time_minutes: 1-12> <1-64> ERPS gr
Command Guide of MGSW-28240F Command: erps <1-64> rpl owner { port0 | port1 } port0 ERPS Port 0 interface port1 ERPS Port 1 interface De
Command Guide of MGSW-28240F Example 2: To create a profile 2 and configure the Sub ERPS interface port 0(GigabitEthernet 1/3), port 1(GigabitEthern
Command Guide of MGSW-28240F Example: To configure ERPS version 1 for the specific profile 1. Switch# configure terminal Switch (config)# erps 1 ver
Command Guide of MGSW-28240F To exit configure terminal mode. Switch# configure terminal Switch (config)# exit # 4.2.52 green-ethernet led interval
Command Guide of MGSW-28240F Default: N/A Usage Guide: To configure LED Power on-event to trigger LED light Example: To configure LED Power on-e
Command Guide of MGSW-28240F 4.2.56.114 spanning-tree restricted-role...
Command Guide of MGSW-28240F 4.2.55 hostname Command: hostname < WORD > < WORD > This system's network name Default: N/A
Command Guide of MGSW-28240F 4.2.56.1 access-list action permit Command: access-list action permit action Access list action Default: Pe
Command Guide of MGSW-28240F Command: access-list logging logging Logging frame information. Note: The logging feature only works when th
Command Guide of MGSW-28240F 4.2.56.5 access-list port-state Command: access-list port-state port-state Re-enable shutdown port that was shu
Command Guide of MGSW-28240F 4.2.56.7 access-list redirect interface Command: access-list redirect interface 10GigabitEthernet <port_type_list>
Command Guide of MGSW-28240F 4.2.56.9 aggregation group Command: aggregation group <uint> aggregation Create an aggregation group
Command Guide of MGSW-28240F 4.2.56.11 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Gu
Command Guide of MGSW-28240F 4.2.56.13 dot1x port-control Command: dot1x port-control auto | force-authorized | force-unauthorized | mac-based | mult
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x radius-qos 4.2.56
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x re-authenticate 4.
Command Guide of MGSW-28240F 4.2.57.21 ipv6 mld snooping last-member-query-interval...
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # end Switch# 4.2.56.19 e
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # exit Switch (config)# 4
Command Guide of MGSW-28240F Example: To enable power saving for ports with no link for GigabitEthernet X/X Switch# configure terminal Switch (confi
Command Guide of MGSW-28240F Example: To send GVRP Join-Request(VLAN 1) to GigabitEthernet X/X Switch# configure terminal Switch (config)# interface
Command Guide of MGSW-28240F To configure Check-VLAN mode into ARP inspection for specific interface Example: To configure Check-VLAN mode (Enabled)
Command Guide of MGSW-28240F Default: Trusted Usage Guide: To configure Trusted into ARP inspection for specific interface Example: To c
Command Guide of MGSW-28240F Usage Guide: To apply the IGMP Snooping filter ID for specific interface Example: To apply the IGMP Snooping filter ID
Command Guide of MGSW-28240F Example: To limit 5 groups of IGMP for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface Gigabi
Command Guide of MGSW-28240F To enable IP Source Guard for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet
Command Guide of MGSW-28240F Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping filter
Comments to this Manuals