Planet WGSW-48040HP User Manual

Command Guide of WGSW-48040HP 4.2.74.3 do ...

Command Guide of WGSW-48040HP 4.2.45.60 media-type Command: media-type dual | rj45 | sfp media-type Media type. dual Dual media interface (co

Command Guide of WGSW-48040HP 4.2.45.62 mvr immediate-leave Command: mvr immediate-leave mvr Multicast VLAN Registration configuratio

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mvr name 111 type sourc

Command Guide of WGSW-48040HP Usage Guide: To enable SSM of SyncE for specific interface Example: To enable SSM of SyncE for GigabitEthernet X/X S

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To run Ping function for specific interface Example: To run Ping function (IP address: 1

Command Guide of WGSW-48040HP pdcheck Allows user to enable or disable per port PD Alive Check function. IP To set PoE devic

Command Guide of WGSW-48040HP 4.2.45.71 poe pdcheck enable Command: poe pdcheck enable poe Power Over Ethernet. pdcheck Allows user

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck interval 10

Command Guide of WGSW-48040HP To configure PD Ping Alive Check retry count of PoE for specific interface. Example: To configure PD Ping Alive Check r

Command Guide of WGSW-48040HP low Set priority to low. Default: 2 Usage Guide: To configure interface priority of PoE for specific i

Command Guide of WGSW-48040HP 4.2.97 logging on...

Command Guide of WGSW-48040HP Command: port-security port-security Enable/disable port security per interface. Default: Disabled Usage Gui

Command Guide of WGSW-48040HP 4.2.45.80 port-security violation Command: port-security violation [protect | shutdown | trap | trap-shutdown] port-sec

Command Guide of WGSW-48040HP To configure protected mode (trap-shutdown) of Port-security for GigabitEthernet X/X Switch# configure terminal Switc

Command Guide of WGSW-48040HP To enable PVLAN isolation for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEther

Command Guide of WGSW-48040HP Usage Guide: To configure DEI of QoS for specific interface Example: To configure DEI (1) of QoS for GigabitEthernet

Command Guide of WGSW-48040HP zero Classify to new DSCP if DSCP is 0 Default: Disabled Usage Guide: To configure DSCP Classify of QoS for

Command Guide of WGSW-48040HP qos dscp-translate qos Quality of Service dscp-translate DSCP ingress translation Default: Disabled

Command Guide of WGSW-48040HP To configure (QoS class, DP level) to (PCP, DEI) Mapping of QoS as below table for GigabitEthernet X/X Switch# configur

Command Guide of WGSW-48040HP 4.2.45.92 qos pcp Command: qos pcp <Pcp : 0-7> qos Quality of Service pcp Priority Code Poi

Command Guide of WGSW-48040HP 4.2.45.94 qos queue-policer queue Command: qos queue-policer queue <Queue : 0~7> <Rate : 100-13200000> qo

Command Guide of WGSW-48040HP 4.2.132.6 reboot-only ...

Command Guide of WGSW-48040HP Example: To configure Egress Queue (4) Shapers Rate (9999 Kbps) of QoS for GigabitEthernet X/X Switch# configure term

Command Guide of WGSW-48040HP Default: 500 Usage Guide: To configure Broadcast Frames Storm Control Rate of QoS for specific interface Example:

Command Guide of WGSW-48040HP qos storm unknown <Rate : 100-13200000> [fps] qos Quality of Service storm Storm policer unknown

Command Guide of WGSW-48040HP Switch (config-if) # qos tag-remark pcp 1 dei 1 4.2.45.101 qos tag-remark mapped Command: qos tag-remark mapped qos

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos trust dscp 4.2.45

Command Guide of WGSW-48040HP To configure RMON History Configuration for specific interface Example: To configure RMON History Configuration as belo

Command Guide of WGSW-48040HP 4.2.45.106 shutdown Command: shutdown shutdown Shutdown of the interface. Default: No shutdown Usage Guide:

Command Guide of WGSW-48040HP Command: spanning-tree auto-edge spanning-tree Spanning Tree protocol auto-edge Auto detects edge statu

Command Guide of WGSW-48040HP Command: spanning-tree edge spanning-tree Spanning Tree protocol edge Edge port Default: Non-Edg

Command Guide of WGSW-48040HP 4.2.45.112 spanning-tree mst <Instance : 0-7> cost Command: spanning-tree mst <Instance : 0-7> cost <Cos

Command Guide of WGSW-48040HP 4.2.163.1 do ...

Command Guide of WGSW-48040HP To enable Path Cost (32) of CIST / MST Normal Port Configuration (CIST) for GigabitEthernet X/X Switch# configure termi

Command Guide of WGSW-48040HP To enable Restrict topology change notifications of CIST Normal Port Configuration for GigabitEthernet X/X Switch# conf

Command Guide of WGSW-48040HP <vlan_id> VLAN ID of the VLAN when this port is in access mode Default: 1 Usage Guide: To configure acce

Command Guide of WGSW-48040HP 4.2.45.119 switchport forbidden vlan remove Command: switchport forbidden vlan remove <vlan_list> switchport Sw

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport hybrid acce

Command Guide of WGSW-48040HP hybrid Change PVID for hybrid port egress-tag Egress VLAN tagging configuration all Tag all frames none

Command Guide of WGSW-48040HP 4.2.45.124 switchport hybrid native vlan Command: switchport hybrid native vlan <vlan_id> switchport Swit

Command Guide of WGSW-48040HP To enable Port type (Unaware) in Hybrid VLAN mode for GigabitEthernet X/X Switch# configure terminal Switch (config)#

Command Guide of WGSW-48040HP id id keyword <1-128> Unique VCE ID for each VCL entry (1-128) <ipv4_subnet> Source IP address

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport vlan mac 0

Command Guide of WGSW-48040HP 4.4.1 debug ...

Command Guide of WGSW-48040HP <word16> Group Name (Range: 1 - 16 characters) vlan vlan keyword <vlan_id> VLAN ID required for

Command Guide of WGSW-48040HP Switch (config-if) # switchport voice vlan discovery-protocol lldp 4.2.45.132 switchport voice vlan mode Command: swi

Command Guide of WGSW-48040HP Disabled Usage Guide: To enable Voice VLAN security for specific interface Example: To enable Voice VLAN security for

Command Guide of WGSW-48040HP Usage Guide: To run exec commands in configure terminal mode Example: To run “show aaa” in configure terminal mode.

Command Guide of WGSW-48040HP Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Sw

Command Guide of WGSW-48040HP 4.2.46.5 ip address dhcp Command: ip address dhcp ip Interface Internet Protocol config commands address Ad

Command Guide of WGSW-48040HP Switch (config)# interface vlan X Switch (config-if-vlan)# ip address dhcp fallback 192.168.1.10 255.255.255.0 4.2.46.

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping 4.2.46.9 ip ig

Command Guide of WGSW-48040HP last-member-query-interval Last Member Query Interval in tenths of seconds <IpmcLmqi : 0-31744> 0 - 317

Command Guide of WGSW-48040HP 4.2.46.12 ip igmp snooping querier address Command: ip igmp snooping querier address <ipv4_ucast>

Command Guide of WGSW-48040HP 4.20 show...

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping querier election

Command Guide of WGSW-48040HP Default: 125 Usage Guide: To configure Querier-interval of IGMP snooping for specific VLAN Example: To configure

Command Guide of WGSW-48040HP ip igmp snooping unsolicited-report-interval <IpmcUri : 0-31744> ip Interface Internet Protocol config co

Command Guide of WGSW-48040HP 4.2.46.19 ipv6 mld snooping Command: ipv6 mld snooping ipv6 IPv6 configuration commands mld Multicast L

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping compatibility v2

Command Guide of WGSW-48040HP 0 Usage Guide: To configure CoS priority of MLD snooping for specific VLAN Example: To configure CoS priority (5) of

Command Guide of WGSW-48040HP query-interval Query Interval in seconds <IpmcQi : 1-31744> 1 - 31744 seconds Default: 125 Usage Gu

Command Guide of WGSW-48040HP Command: ipv6 mld snooping robustness-variable <IpmcRv : 1-255> ipv6 IPv6 configuration commands mld

Command Guide of WGSW-48040HP Switch (config-if-vlan)# ipv6 mld snooping unsolicited-report-interval 99 4.2.46.28 no Command: no no Negate a co

Command Guide of WGSW-48040HP Switch (config)# ip arp inspection 4.2.48 ip arp inspection entry interface Command: ip arp inspection entry interfac

Command Guide of WGSW-48040HP 4.20.41 show ip name-server ...

Command Guide of WGSW-48040HP arp Address Resolution Protocol inspection ARP inspection translate arp inspection translate all en

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# ip arp inspection translate interface GigabitEthernet 1/1 1 00:11:22:33:44

Command Guide of WGSW-48040HP excluded-address Prevent DHCP from assigning certain addresses <A.B.C.D> Low IP address Default: N/

Command Guide of WGSW-48040HP 4.2.53.1 broadcast Command: broadcast <A.B.C.D> broadcast Broadcast address in use on the client's subnet

Command Guide of WGSW-48040HP 4.2.53.3 client-identifier mac-address Command: client-identifier mac-address <MAC> client-identifier Client i

Command Guide of WGSW-48040HP 4.2.53.5 default-router Command: default-router <A.B.C.D> default-router Default routers <A.B.C.D>

Command Guide of WGSW-48040HP 4.2.53.7 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Gu

Command Guide of WGSW-48040HP Switch (config-dhcp-pool)# domain-name planet.com 4.2.53.9 end Command: end end Go back to EXEC mode Def

Command Guide of WGSW-48040HP Switch (config-dhcp-pool)# exit Switch (config)# 4.2.53.11 hardware-address Command: hardware-address <MAC>

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# host 192.168.1.10 2

Command Guide of WGSW-48040HP 4.20.82 show pvlan isolation ...

Command Guide of WGSW-48040HP To configure NetBIOS Name Server of DHCP Server. Example: To configure NetBIOS Name Server (192.168.1.10) of DHCP Serve

Command Guide of WGSW-48040HP Default: None Usage Guide: To configure NetBIOS scope of DHCP Server. Example: To configure NetBIOS scope (planet)

Command Guide of WGSW-48040HP Default: None Usage Guide: To configure NIS Domain Name of DHCP Server Example: To configure NIS Domain Name (pla

Command Guide of WGSW-48040HP N/A Usage Guide: To default the function Example: To disable the function (nis-domain-name planet.com) for pool “plan

Command Guide of WGSW-48040HP <HEX-VALUE> Hex values in 64 octets Default: None Usage Guide: To configure Vendor ID and info of DHCP S

Command Guide of WGSW-48040HP ip Internet Protocol helper-address DHCP relay server <Ip : ipv4_ucast> IP address of the DHCP

Command Guide of WGSW-48040HP ip Internet Protocol http Hypertext Transfer Protocol secure-server Secure HTTP web server

Command Guide of WGSW-48040HP ip Internet Protocol igmp Internet Group Management Protocol host-proxy IGMP proxy configuratio

Command Guide of WGSW-48040HP ip igmp snooping vlan <vlan_list> ip Internet Protocol igmp Internet Group Management Protoco

Command Guide of WGSW-48040HP 4.2.63 ip igmp unknown-flooding Command: ip igmp unknown-flooding ip Internet Protocol igmp Internet

Command Guide of WGSW-48040HP Chapter 1 COMMAND LINE INTERFACE 1.1 Accessing the CLI When accessing the management interface for the switch over a

Command Guide of WGSW-48040HP 4.2.65 ip name-server dhcp Command: ip name-server dhcp ip Internet Protocol name-server Domain Name

Command Guide of WGSW-48040HP 4.2.67 ip route Command: ip route <ipv4_addr> <ipv4_netmask> <ipv4_gateway> ip Internet

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# ip routing 4.2.69 ip source binding interface Command: ip source binding

Command Guide of WGSW-48040HP Default: None Usage Guide: To enable SSH service Example: To enable SSH service Switch# configure terminal Swit

Command Guide of WGSW-48040HP Default: Disabled Usage Guide: To translate dynamic entries to IP Source Guard table Example: To translate dyna

Command Guide of WGSW-48040HP Default: Disabled Usage Guide: To enter IPMC profile mode Example: To enter IPMC profile mode (planet) Switch# co

Command Guide of WGSW-48040HP Default: None Usage Guide: To configure description for specific IPMC Profile Example: To configure description (

Command Guide of WGSW-48040HP end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EX

Command Guide of WGSW-48040HP no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function. Example: To e

Command Guide of WGSW-48040HP Command: ipv6 mld host-proxy ipv6 IPv6 configuration commands mld Multicast Listener Discovery host-

Command Guide of WGSW-48040HP The CLI provides the following modes:  User Mode When the operator logs into the CLI, the User Mode is the initia

Command Guide of WGSW-48040HP 4.2.77 ipv6 mld snooping Command: ipv6 mld snooping ipv6 IPv6 configuration commands mld Multicast Liste

Command Guide of WGSW-48040HP 4.2.79 ipv6 mld ssm-range Command: ipv6 mld ssm-range <ipv6_mcast> <Ipv6PrefixLength : 8-128> ipv6

Command Guide of WGSW-48040HP 4.2.81 ipv6 route Command: Ipv6 route <X:X:X:X::X/<0-128>> {<X:X:X:X::X>, interface vlan <vlan_id

Command Guide of WGSW-48040HP 4.2.82 lacp system-priority Command: lacp system-priority <1-65535> lacp LACP settings system-priority

Command Guide of WGSW-48040HP 4.2.83.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To r

Command Guide of WGSW-48040HP Switch (config-line)# editing 4.2.83.3 end Command: end end Go back to EXEC mode Default: None Usage

Command Guide of WGSW-48040HP Switch (config-line)# exec-banner 4.2.83.5 exec-timeout Command: exec-timeout <0-1440> exec-timeout Set

Command Guide of WGSW-48040HP Switch (config-line)# exec-timeout 10 4.2.83.7 exit Command: exit exit Exit from current mode

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# history size 1 4.2.83.9 length Command:

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# location taiwan 4.2.83.11 motd-banner Com

Command Guide of WGSW-48040HP Contents Chapter 1 COMMAND LINE INTERFACE... 18 1.1 Accessing the

Command Guide of WGSW-48040HP Chapter 2 CONSOLE CLI MANAGEMENT 2.1 Terminal Setup To configure the system, connect a serial cable to a COM port on a P

Command Guide of WGSW-48040HP Switch (config)# line vty 1 Switch (config-line)# no motd-banner 4.2.83.13 privilege level Command: privilege level &

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# width 50 4.2.84 lldp holdtime Command: l

Command Guide of WGSW-48040HP Usage Guide: To configure Datum type of LLDP Example: To configure Datum type (nad83-mllw) of LLDP Switch# configu

Command Guide of WGSW-48040HP meters Specify the altitude in meters. Default: 0 Usage Guide: To configure altitude of LLDP-MED Example: T

Command Guide of WGSW-48040HP lldp LLDP configurations. med Media Endpoint Discovery location-tlv LLDP-MED Location Type

Command Guide of WGSW-48040HP Switch (config)# lldp med location-tlv longitude east 5 4.2.91 lldp med media-vlan-policy Command: lldp med media-vla

Command Guide of WGSW-48040HP Switch (config)# lldp med media-vlan-policy 1 guest-voice tagged 1 dscp 45 l2-priority 5 4.2.92 lldp reinit Command:

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# lldp timer 555 4.2.94 lldp transmission-delay Command: lldp transmission

Command Guide of WGSW-48040HP Example: To configure address of log server Switch# configure terminal Switch (config)# logging host 192.168.5.5 4.2

Command Guide of WGSW-48040HP Usage Guide: To enable log server Example: To enable log server Switch# configure terminal Switch (config)# loggi

Command Guide of WGSW-48040HP Figure 2-3 Hyper Terminal COM Port Configuration You can change these settings, if desired, after you log on. This man

Command Guide of WGSW-48040HP Usage Guide: To configure shutdown time interval of Loop Protection Example: To configure shutdown time interval (8

Command Guide of WGSW-48040HP Usage Guide: To configure Aging Time of MAC Address Table Example: To configure Aging Time (888) of MAC Address Tab

Command Guide of WGSW-48040HP 4.2.103 monitor destination Command: monitor destination interface 10GigabitEthernet <port_type_list> | GigabitEt

Command Guide of WGSW-48040HP 4.2.105 mvr Command: mvr mvr Multicast VLAN Registration configuration Default: Disabled Usage Guide: To enabl

Command Guide of WGSW-48040HP 4.2.107 mvr name <mvr_name> frame priority Command: mvr name <mvr_name> frame priority <CosPriority : 0-

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# mvr name 123 frame tagged 4.2.109 mvr name <mvr_name> igmp-address C

Command Guide of WGSW-48040HP Usage Guide: To configure the Last Member Query Interval of MVR profile Example: To configure the Last Member Query

Command Guide of WGSW-48040HP Default: None Usage Guide: To create a profile of MVR VLAN Example: To create a profile of MVR VLAN (5) Switch#

Command Guide of WGSW-48040HP <vlan_list> MVR multicast VLAN list frame MVR control frame in TX priority Interface CoS priority &

Command Guide of WGSW-48040HP 4.2.116 mvr vlan <vlan_list> igmp-address Command: mvr vlan <vlan_list> igmp-address <ipv4_ucast> mvr

Command Guide of WGSW-48040HP 2.2 Logon to the Console Once the terminal is connected to the device, power on the Managed Switch, and the terminal wil

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# mvr vlan 123 last-member-query-interval 500 4.2.118 mvr vlan <vlan_list

Command Guide of WGSW-48040HP Usage Guide: To configure profile name of MVR VLAN Example: To configure profile name (6) of MVR VLAN (5) Switch#

Command Guide of WGSW-48040HP Example: To enable the NTP service Switch# configure terminal Switch (config)# ntp 4.2.122 ntp server Command: nt

Command Guide of WGSW-48040HP Default: Enabled Usage Guide: To enable System PoE Admin Mode. Example: To enable System PoE Admin Mode. Switch

Command Guide of WGSW-48040HP 4.2.125 poe sequential enable Command: poe sequential enable poe Power Over Ethernet sequential PoE sequent

Command Guide of WGSW-48040HP 4.2.127 poe sequential rule Command: poe sequential rule { port | priority } poe Power Over Ethernet sequential r

Command Guide of WGSW-48040HP 4.2.129 poe temperature-protection enable Command: poe temperature-protection enable poe Power Over Ethernet temp

Command Guide of WGSW-48040HP 4.2.131 poe usage-threshold Command: poe usage-threshold <1-99> poe Power Over Ethernet usage-threshold

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)# 4.2.132.1 do Co

Command Guide of WGSW-48040HP Example: To back to EXEC mode Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-t

Command Guide of WGSW-48040HP  Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the curr

Command Guide of WGSW-48040HP Example: To enable the function (description 999). Switch# configure terminal Switch (config)# poe-time-range profil

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)# periodic Mon 11 59

Command Guide of WGSW-48040HP 4.2.133 port-security Command: port-security port-security Enable/disable port security globally Default: Disa

Command Guide of WGSW-48040HP 4.2.135 port-security aging time Command: port-security aging time <10-10000000> port-security Enable/disabl

Command Guide of WGSW-48040HP <cmd> Initial valid words and literals of the command to modify Default: None Usage Guide: To configure t

Command Guide of WGSW-48040HP cs3 Class Selector PHB CS3 precedence 3(DSCP 24) cs4 Class Selector PHB CS4 precedence 4(DSCP 32)

Command Guide of WGSW-48040HP be Default PHB(DSCP 0) for best effort traffic cs1 Class Selector PHB CS1 precedence 1(DSCP 8) cs2

Command Guide of WGSW-48040HP af33 Assured Forwarding PHB AF33(DSCP 30) af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assu

Command Guide of WGSW-48040HP <DscpNum : 0-63> Specific DSCP af11 Assured Forwarding PHB AF11(DSCP 10) af12 Assured Forwa

Command Guide of WGSW-48040HP va } } to { <dscp_num_tr> | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af

Command Guide of WGSW-48040HP 4. Repeat step 1 to check if the IP address is changed.  Store current switch configuration 5. At the “#” prompt, en

Command Guide of WGSW-48040HP 4.2.142 qos qce Command: qos qce <qce_id> [ { next <qce_id_next> } | last ] [ interface ( <port_type&g

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# qos qce 1 interface GigabitEthernet 1/1-2 tag type tagged vid 5 pcp 3 de

Command Guide of WGSW-48040HP [ pcp-dei { <action_pcp> <action_dei> | default } ] [ dscp { <action_dscp_dscp> | { be | af11 | af12 |

Command Guide of WGSW-48040HP Example: To refresh the QCE. Switch# configure terminal Switch (config)# qos qce refresh 4.2.145 qos wred Comman

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# qos wred queue 1 min-th 2 mdp-1 3 mdp-2 4 mdp-3 5 4.2.146 radius-serve

Command Guide of WGSW-48040HP Default: None Usage Guide: To configure the NAS-IP-Address Example: To configure the NAS-IP-Address (7.7.7.7) Swi

Command Guide of WGSW-48040HP Default: 0 Usage Guide: To configure the Deadtime of Radius-Server Example: To configure the Deadtime (15) of Radi

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# radius-server host planet.com.tw timeout 10 retransmit 6 key 123456789 4

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# radius-server retransmit 5 4.2.153 radius-server timeout Command:

Command Guide of WGSW-48040HP normal ifInErrors The number of inbound packets that contained errors preventing

Command Guide of WGSW-48040HP Chapter 3 TELNET CLI MANAGEMENT 3.1 Telnet Login The Managed Switch also supports telnet for remote management. The swit

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# rmon alarm 1 .1.3.6.1.2.1.2.2.1.10.15 50 absolute rising-threshold 1000 1

Command Guide of WGSW-48040HP Default: None Usage Guide: To configure the SFP temperature-threshold of sFlow Example: To configure the SFP temp

Command Guide of WGSW-48040HP any any security model v1 v1 security model v2c v2c security model v3 v3 security model

Command Guide of WGSW-48040HP <ipv4_addr> IPv4 address <ipv4_netmask> IPv4 netmask Default: None Usage Guide: To confi

Command Guide of WGSW-48040HP 4.2.161 snmp-server engine-id Command: snmp-server engine-id local <Engineid : word10-32> snm

Command Guide of WGSW-48040HP 4.2.162.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To r

Command Guide of WGSW-48040HP Switch# 4.2.162.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit

Command Guide of WGSW-48040HP Usage Guide: To configure Trap Host of SNMP Example: To configure Trap Host (below table) of SNMP Switch# configure

Command Guide of WGSW-48040HP <Retries : 0-255> retires times timeout timeout parmater <Timeout : 0-2147> timeout int

Command Guide of WGSW-48040HP 4.2.162.8 traps Command: traps [ aaa authentication ] [ system [ coldstart ] [ warmstart ] ] [ switch [ stp ] [ rmon ]

Command Guide of WGSW-48040HP Chapter 4 Commands for CLI Configuration 4.1 clear 4.1.1 clear access management statistics Command: clear access mana

Command Guide of WGSW-48040HP engineID Configure trap server's engine ID probe Probe trap server's engine ID Default:

Command Guide of WGSW-48040HP Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec command

Command Guide of WGSW-48040HP 4.2.163.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mod

Command Guide of WGSW-48040HP 4.2.163.5 spanning-tree auto-edge Command: spanning-tree auto-edge spanning-tree Spanning Tree protocol auto-edge

Command Guide of WGSW-48040HP 4.2.163.7 spanning-tree edge Command: spanning-tree edge spanning-tree Spanning Tree protocol edge Edge

Command Guide of WGSW-48040HP Switch (config-snmps-host)# spanning-tree link-type shared 4.2.163.9 spanning-tree mst <instance> cost

Command Guide of WGSW-48040HP Usage Guide: To configure the Port Priority of MSTI Port Example: To configure the Port Priority (96) of MSTI Port (M

Command Guide of WGSW-48040HP Usage Guide: To enable the Restricted TCN of CIST Example: To enable the Restricted TCN of CIST Switch# configure te

Command Guide of WGSW-48040HP 4.2.165 tacacs-server deadtime Command: tacacs-server deadtime <minutes> tacacs-server Configure TACA

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# tacacs-server host planet.com port 55 timeout 6 key 7788 4.2.167 transp

Command Guide of WGSW-48040HP 4.1.3 clear dot1x statistics interface Command: clear dot1x statistics interface GigabitEthernet | 10GigabitEthernet

Command Guide of WGSW-48040HP <title> email title Default: N/A Usage Guide: To configure SMTP sender's email address and title of

Command Guide of WGSW-48040HP Command: transport email to <1 | 2> <mail_addr> transport Enable or disable transport email

Command Guide of WGSW-48040HP Command: upnp advertising-duration <100-86400> upnp Set UPnP's configurations advertising-dur

Command Guide of WGSW-48040HP 4.2.174 username Command: username <username> privilege <priv> password { encrypted <encry_password&g

Command Guide of WGSW-48040HP <vlan_list> VLAN IDs 1~4095 Default: None Usage Guide: To create the VLAN Profiles Example: To creat

Command Guide of WGSW-48040HP 4.2.175.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Exa

Command Guide of WGSW-48040HP 4.2.175.4 name Command: name <vlan_name> name ASCII name of the VLAN <vword32> The ASCII nam

Command Guide of WGSW-48040HP 4.2.176 vlan ethertype s-custom-port Command: vlan ethertype s-custom-port <etype> vlan VLA

Command Guide of WGSW-48040HP snap-8021h SNAP OUI is 8021h group Protocol-based VLAN group commands <grp_id> Group Name (R

Command Guide of WGSW-48040HP 4.2.179 voice vlan aging-time Command: voice vlan aging-time <aging_time> voice Voice appliance attributes

Command Guide of WGSW-48040HP Usage Guide: To clear the DHCP detailed statistics for all. Example: To clear the Switch’s DHCP detailed statistics f

Command Guide of WGSW-48040HP 4.2.181 voice vlan oui Command: voice vlan oui <oui> [ description <description> ] voice Voice appli

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# voice vlan vid 66 4.2.183 web privilege group Command: web privile

Command Guide of WGSW-48040HP 4.3 copy 4.3.1 copy Command: copy { startup-config | running-config | <source_path> } { startup-config | running

Command Guide of WGSW-48040HP Example: To configure Description (1233) of Debug Prompt Switch # debug prompt 1233 1233# 4.5 delete 4.5.1 delete C

Command Guide of WGSW-48040HP rw 1970-01-01 07:26:26 1833 startup-config 2 files, 2481 bytes total. 4.6 dir 4.6.1 dir Command: dir di

Command Guide of WGSW-48040HP Usage Guide: To exit enable mode Example: To exit enable mode Switch # disable Switch > 4.8 do 4.8.1 do Comman

Command Guide of WGSW-48040HP dot1x initialize [ interface ( <port_type> [ <plist> ] ) ] dot1x IEEE Standard for port-based Netwo

Command Guide of WGSW-48040HP 4.11 exit 4.11.1 exit Command: exit exit Exit from EXEC mode Default: None Usage Guide: To exit EXEC mode E

Command Guide of WGSW-48040HP Switch # firmware swap 4.12.2 firmware upgrade Command: firmware upgrade <tftpserver_path_file> firmware

Command Guide of WGSW-48040HP Usage Guide: To do DHCP renew for specific VLAN Example: To do DHCP renew for specific VLAN (6) Switch # ip dhcp ret

Command Guide of WGSW-48040HP 4.1.8 clear ip dhcp detailed statistics server Command: clear ip dhcp detailed statistics server Default: N/A Usage G

Command Guide of WGSW-48040HP Default: None Usage Guide: To view the file Example: To view the file (222) Switch # copy running-config flash:222

Command Guide of WGSW-48040HP Switch# no erps 1 command force port0 4.17 ping 4.17.1 ping ip Command: ping ip <v_ip_addr> [ repeat <cou

Command Guide of WGSW-48040HP 4.17.2 ping ipv6 Command: ping ipv6 <v_ipv6_addr> [ repeat <count> ] [ size <size> ] [ interval <

Command Guide of WGSW-48040HP reload cold reload Reload system cold Reload cold. Default: N/A Usage Guide: To restart the device.

Command Guide of WGSW-48040HP send { * | console 0 | vty <vty_list> } <message> reload Reload system * All tty lines

Command Guide of WGSW-48040HP Usage Guide: To display the AAA services. Example: To display the AAA services Switch # show aaa console : local t

Command Guide of WGSW-48040HP 4.20.3 show access-list Command: show access-list [ interface [ ( <port_type> [ <v_port_type_list> ] ) ]

Command Guide of WGSW-48040HP GigabitEthernet 1/1 : --------------------- GigabitEthernet 1/1 access-list action is permit GigabitEthernet 1/1 access-

Command Guide of WGSW-48040HP Switch access-list rate limiter ID 5 is 1 pps Switch access-list rate limiter ID 6 is 1 pps Switch access-list rate limi

Command Guide of WGSW-48040HP loop-protect The ACEs that are configured by Loop Protect module mep The ACEs that are configured by

Command Guide of WGSW-48040HP 4.1.20 clear ip statistics system icmp interface vlan ...

Command Guide of WGSW-48040HP Usage Guide: To clear the DHCP relay statistics. Example: To clear the Switch’s DHCP relay statistics. Switch# clear

Command Guide of WGSW-48040HP show Show running system information aggregation Aggregation port configuration mode Traffic

Command Guide of WGSW-48040HP 4.20.8 show clock Command: show clock show Show running system information clock Configure time-of-

Command Guide of WGSW-48040HP Daylight Saving Time Mode : Disabled. Daylight Saving Time Start Time Settings : Week: 0 Day: 0

Command Guide of WGSW-48040HP Switch # show dot1x statistics all interface GigabitEthernet 1/1 GigabitEthernet 1/1 EAPOL Statistics: Rx Total:

Command Guide of WGSW-48040HP Switch # show dot1x status GigabitEthernet 1/1 : --------------------- Admin State Port State Last S

Command Guide of WGSW-48040HP 4.20.13 show green-ethernet energy-detect Command: show green-ethernet energy-detect [ interface ( <port_type> [

Command Guide of WGSW-48040HP 4.20.15 show history Command: show history show Show running system information history Display t

Command Guide of WGSW-48040HP Usage Guide: To display the SFP Transceiver information. Example: To display the SFP Transceiver information for in

Command Guide of WGSW-48040HP Interface Rx Octets Tx Octets ---------------------- ------------------ ------------------ Gig

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the VLAN mode. Example: To display the VLAN mode for interface GigabitEther

Command Guide of WGSW-48040HP 4.1.13 clear ip dhcp server binding expired Command: clear ip dhcp server binding expired Default: N/A Usage Guide:

Command Guide of WGSW-48040HP Switch # show interface GigabitEthernet 1/1 veriphy Starting VeriPHY - Please wait Interface Pair A Lengt

Command Guide of WGSW-48040HP Command: show interface vlan [ <vlist> ] show Show running system information interface Interfa

Command Guide of WGSW-48040HP 4.20.24 show ip arp inspection Command: show ip arp inspection show Show running system information ip I

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the ARP Inspection Configuration. Example: To display the ARP Inspection Co

Command Guide of WGSW-48040HP 4.20.27 show ip dhcp detailed statistics Command: show ip dhcp detailed statistics { server | client | snooping | relay

Command Guide of WGSW-48040HP Rx Release: 0 Tx Release: 0 Rx Inform: 0

Command Guide of WGSW-48040HP 4.20.29 show ip dhcp pool Command: show ip dhcp pool [ <pool_name> ] show Show running system information

Command Guide of WGSW-48040HP 4.20.30 show ip dhcp relay Command: show ip dhcp relay [ statistics ] show Show running system information

Command Guide of WGSW-48040HP Switch # show ip dhcp server DHCP server is globally disabled. All VLANs are disabled. 4.20.32 show ip dhcp serv

Command Guide of WGSW-48040HP 4.20.33 show ip dhcp server declined-ip (GG) Command: show ip dhcp server declined-ip show Show running system

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To clear the IGMP snooping statistics. Example: To clear the Switch’s IGMP snooping stati

Command Guide of WGSW-48040HP Database Counters ========================= POOL 2 Excluded IP 1 Declined IP

Command Guide of WGSW-48040HP interface Select an interface to configure Default: N/A Usage Guide: To display the DHCP Snooping confi

Command Guide of WGSW-48040HP ip Internet Protocol http Hypertext Transfer Protocol server HTTP web server secure Secu

Command Guide of WGSW-48040HP Switch # show ip igmp snooping detail IGMP Snooping is disabled to stop snooping IGMP control plane. Multicast streams

Command Guide of WGSW-48040HP interface IP interface status and configuration brief Brief IP interface status Default: N/A Usa

Command Guide of WGSW-48040HP 4.20.42 show ip route Command: show ip route show Show running system information ip Internet Protocol

Command Guide of WGSW-48040HP Example: To display the Static IP Source Guard Table. Switch # show ip source binding interface GigabitEthernet 1/1

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the IP statistics. Example: To display the IP statistics. Switch # show

Command Guide of WGSW-48040HP IPv4 ICMP statistics: Rcvd: 2618 Messages, 0 Error Sent: 2618 Messages, 0 Error ICMP message statistics:

Command Guide of WGSW-48040HP 4.20.47 show ipmc profile Command: show ipmc profile [ <profile_name> ] [ detail ] show Show running syst

Command Guide of WGSW-48040HP Example: To clear the Switch’s IPv4 ICMP traffic for designated message type 0. Switch# clear ip statistics icmp icmp-

Command Guide of WGSW-48040HP Example: To display the IP Multicast Range. Switch # show ipmc range Range Name : 1 Start Address: 224.24.24.24 En

Command Guide of WGSW-48040HP 3 local destination, 0 forwarding 0 header error, 0 address error, 0 unknown protocol 0 no ro

Command Guide of WGSW-48040HP MLD Snooping is disabled to stop snooping MLD control plane. Multicast streams destined to unregistered MLD groups will

Command Guide of WGSW-48040HP vlan VLAN of IPv6 interface Default: N/A Usage Guide: To display the IPv6 neighbor information. Examp

Command Guide of WGSW-48040HP 4.20.54 show ipv6 statistics Command: show ipv6 statistics [ system ] [ interface vlan <vlan_list> ] [ icmp ]

Command Guide of WGSW-48040HP IP interface statistics: IPv6 Statistics on Interface VLAN: 1 Rcvd: 12 total in 1032 bytes 3 local dest

Command Guide of WGSW-48040HP lacp LACP configuration/status internal Internal LACP configuration neighbour Neighbour LACP s

Command Guide of WGSW-48040HP * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is e

Command Guide of WGSW-48040HP PDU stats ----------- Information PDU TX: 0 Information PDU RX: 0 Variable

Command Guide of WGSW-48040HP Example: To display the LLDP-MED policy information. Switch # show lldp med media-vlan-policy Policy Id Application

Command Guide of WGSW-48040HP 4.1.20 clear ip statistics system icmp interface vlan Command: clear ip statistics system icmp interface vlan <vl

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the LLDP neighbors information. Example: To display the LLDP neighbors

Command Guide of WGSW-48040HP 4.20.62 show logging Command: show logging {<log_id> | error | info | warning } [ switch <switch_list> ]

Command Guide of WGSW-48040HP Example: To display the Loop protection information for GigabitEthernet 1/1. Switch # show loop-protect interface Gig

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the MAC address table. Example: To display the MAC address table for VLAN 1

Command Guide of WGSW-48040HP Usage Guide: To display the MEP information. Example: To display the MEP instance 1 information. Switch # show m

Command Guide of WGSW-48040HP IGMP MVR VLAN 1 (Name is 1) interface is enabled. Querier status is IDLE RX IGMP Query:0 V1Join:0 V2Join:0 V3Join:0 V2Le

Command Guide of WGSW-48040HP LOL: FALSE DHOLD: TRUE SSM State is: Interface Tx SSM Rx SSM Mode GigabitEthernet 1/1

Command Guide of WGSW-48040HP show Show running system information platform Platform specific information phy PHYs' inf

Command Guide of WGSW-48040HP 4.20.71 show platform phy id Command: show platform phy id [ interface ( <port_type> [ <port_type_list> ]

Command Guide of WGSW-48040HP Switch # show platform phy status interface GigabitEthernet 1/1 Port Issues seen during 1G PHY warmstart Issu

Command Guide of WGSW-48040HP <vlan_list> VLAN identifier(s): VID Default: N/A Usage Guide: To clear the ipv6 mld snooping statistics fo

Command Guide of WGSW-48040HP interface Search by port Default: N/A Usage Guide: To display the status of Port Security. Example: To d

Command Guide of WGSW-48040HP Command: show ptp <clockinst> { default | current | parent | time-property | filter | servo | clk | ho | uni | ma

Command Guide of WGSW-48040HP --------- --------- ----------------- ----- ---- Ethernet False False 1

Command Guide of WGSW-48040HP Example: To display the slave lock configuration for PTP instance 0. Switch # show ptp 0 slave-cfg Stable Offset Off

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the external clock output configuration. Example: To display the external cl

Command Guide of WGSW-48040HP pvlan PVLAN configuration isolation show isolation configuration interface Search by port Defa

Command Guide of WGSW-48040HP Usage Guide: To display the QoS configuration. Example: To display the QoS configuration for GigabitEthernet 1/1.

Command Guide of WGSW-48040HP qos queue-shaper queue 2 mode: disabled, rate: 500 kbps, excess: disabled qos queue-shaper queue 3 mode: disabled, r

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the RADIUS Server configuration. Example: To display the RADIUS Server conf

Command Guide of WGSW-48040HP SampleType : deltaValue Value : 0 Startup : risingOrFallingAlarm Rising

Command Guide of WGSW-48040HP Example: To clear the Switch’s IPv6 ICMP traffic for designated message type 0. Switch# clear ipv6 statistics icmp icm

Command Guide of WGSW-48040HP rmon RMON statistics history Display the RMON history table Default: N/A Usage Guide: To display t

Command Guide of WGSW-48040HP Data Source : .1.3.6.1.2.1.2.2.1.1.5 etherStatsDropEvents : 3 etherStatsOctets : 10221

Command Guide of WGSW-48040HP line Show line settings console Console vty VTY Default: N/A Usage Guide: To display the ru

Command Guide of WGSW-48040HP 4.20.90 show snmp Command: show snmp show Show running system information snmp Display SNMP configura

Command Guide of WGSW-48040HP SNMPv3 Groups Table; Security Model : v1 Security Name : public Group Name : default_ro_group Security Model : v

Command Guide of WGSW-48040HP View Type : included 4.20.91 show snmp access Command: show snmp access [ <group_name> { v1 | v2c | v3 | any

Command Guide of WGSW-48040HP 4.20.92 show snmp community v3 Command: show snmp community v3 [ <community> ] show Show running system in

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the SNMP Host information. Example: To display the SNMP Host information

Command Guide of WGSW-48040HP IEEE8021-PAE-MIB : - ieee8021paeMIB (.1.0.8802.1.1.1.1) IEEE8023-LAG-MIB : - lagMIBObjects (.1.2.840.10006.300.4

Command Guide of WGSW-48040HP - tcp (.1.3.6.1.2.1.6) - udp (.1.3.6.1.2.1.7) RMON-MIB : - statistics (.1.3.6.1.2.1.16.1) - history (.1.

Command Guide of WGSW-48040HP 4.1.27 clear ipv6 statistics system icmp interface vlan Command: clear ipv6 statistics system icmp interface vlan <

Command Guide of WGSW-48040HP Switch # show snmp mib ifmib ifIndex ifIndex ifDescr Interface ---------- ------

Command Guide of WGSW-48040HP show snmp security-to-group [ { v1 | v2c | v3 } <security_name> ] show Show running system information

Command Guide of WGSW-48040HP Command: show snmp user [ <username> <engineID> ] show Show running system information snmp

Command Guide of WGSW-48040HP Example: To display the SNMP viewer information. Switch # show snmp view View Name : default_view OID Subtree : .1 V

Command Guide of WGSW-48040HP Regional Root: 32768. 00-30-4F-00-99-00 Int. PathCost: 0 Max Hops : 20 TC Flag : Steady TC Count : 0 TC Las

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the TACACS+ Server configuration. Example: To display the TACACS+ Server co

Command Guide of WGSW-48040HP exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 1 hour

Command Guide of WGSW-48040HP Example: To display the user status for all. Switch # show users Line is con 0. * You are at this line now. Co

Command Guide of WGSW-48040HP System Location : System Time : 1970-01-01T22:56:08+00:00 System Uptime : 22:56:08 Active Image ------------ I

Command Guide of WGSW-48040HP Switch # show vlan VLAN Name Interfaces ---- -------------------------------- ---------

Command Guide of WGSW-48040HP N/A Usage Guide: To clear the lldp statistics. Example: To clear the Switch’s lldp statistics. Switch# clear lldp st

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To display the MAC-based VLAN information. Example: To display the MAC-based VLAN inf

Command Guide of WGSW-48040HP To display the Protocol-based VLAN information. Example: To display the Protocol-based VLAN information. Switch #

Command Guide of WGSW-48040HP GigabitEthernet 1/1 switchport voice vlan mode is auto GigabitEthernet 1/1 switchport voice security is disabled Gigabit

Command Guide of WGSW-48040HP EVC 5 10 5 10 Green_Ethernet 5 10 5 10 IP2

Command Guide of WGSW-48040HP editing Enable command line editing Default: Enabled Usage Guide: To enable editing mode for current terminal

Command Guide of WGSW-48040HP size Set history buffer size <history_size> Number of history commands, 0 means disable Default: N

Command Guide of WGSW-48040HP -386- terminal Set terminal line parameters width Set width of the display terminal <lines:0 or 4

Command Guide of WGSW-48040HP 4.1.32 clear logging info error Command: clear logging info error Default: N/A Usage Guide: To clear the logging

Command Guide of WGSW-48040HP 4.2.14 access-list ace...

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To clear the logging warning error. Example: To clear the Switch’s logging warning error.

Command Guide of WGSW-48040HP Switch# clear mac address-table 4.1.37 clear mvr name Command: clear mvr name <MvrName : word16> <MvrName :

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To clear the mvr vlan statistics for specific VLAN. Example: To clear the Switch’s mvr vl

Command Guide of WGSW-48040HP Switch# clear spanning-tree detected-protocols interface * 4.1.42 clear spanning-tree detected-protocols interface Gi

Command Guide of WGSW-48040HP 4.1.44 clear spanning-tree statistics interface GigabitEthernet Command: clear spanning-tree statistics interface Gigab

Command Guide of WGSW-48040HP Default: N/A Usage Guide: To clear the statistics for specific GigabitEthernet port. Example: To clear the Switch’s

Command Guide of WGSW-48040HP Example: To authenticate the local and radius account via console. Switch# configure terminal Switch (config)# aaa aut

Command Guide of WGSW-48040HP 4.2.5 aaa authentication login http radius Command: aaa authentication login http radius Default: http : local Usag

Command Guide of WGSW-48040HP aaa authentication login ssh local Default: ssh : local Usage Guide: To authenticate the local account via ssh only.

Command Guide of WGSW-48040HP Usage Guide: To authenticate the tacacs account via ssh only. Example: To authenticate the local and radius and tacac

Command Guide of WGSW-48040HP 4.2.45.10 description...

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# aaa authentication login telnet local radius 4.2.12 aaa authentication log

Command Guide of WGSW-48040HP To enable the access management profile to allow SNMP / Telnet / HTTP services. Example: To create a Profile 1 enablin

Command Guide of WGSW-48040HP N/A Usage Guide: To create and set up a profile for the access list. Example: To set a Profile 1 up (action: permit,

Command Guide of WGSW-48040HP tag-priority Tag priority vid VID field Default: N/A Usage Guide: To update the specific pro

Command Guide of WGSW-48040HP Command: access-list rate-limiter pps <PpsRate : 0-131071> <PpsRate : 0-131071> Rate value Default:

Command Guide of WGSW-48040HP 4.2.19 banner Command: banner <LINE> <LINE> c banner-text c, where 'c' is a delimiting c

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# banner exec 1 Enter TEXT message. End with the character '1'. g

Command Guide of WGSW-48040HP Username: admin Password: 4.2.22 banner motd Command: banner motd <LINE> <LINE> c banner-text

Command Guide of WGSW-48040HP clock summer-time <WORD> date <Monthstart: 1-12> <Daystart: 1-31> <Yearstart: 1-12> <Timestar

Command Guide of WGSW-48040HP Default: 0 Usage Guide: To default the Rate limiter. Example: To default the Rate limiter ID 1. Switch# configur

Command Guide of WGSW-48040HP 4.2.45.51 lldp tlv-select system-capabilities ...

Command Guide of WGSW-48040HP Example: To set the Re-authenticated Period (777 seconds). Switch# configure terminal Switch (config)# dot1x authen

Command Guide of WGSW-48040HP Switch (config)# dot1x guest-vlan 2 4.2.30 dot1x guest-vlan supplicant Command: dot1x guest-vlan supplicant supplica

Command Guide of WGSW-48040HP 4.2.32 dot1x system-auth-control Command: dot1x system-auth-control Default: Disable Usage Guide: To enable 802.1

Command Guide of WGSW-48040HP Default: 30 Usage Guide: To configure 802.1X EPOAL timeout for Network Access Server Example: To configure 802.1X

Command Guide of WGSW-48040HP Command: enable password level <1-15> <WORD> <1-15> Level number <WORD> The UNENC

Command Guide of WGSW-48040HP To configure enable password(cisco) to encrypted secret in the system configurations and specific level(15) for user Sw

Command Guide of WGSW-48040HP Command: exit Default: N/A Usage Guide: To exit configure terminal mode. Example: To exit configure terminal mod

Command Guide of WGSW-48040HP Usage Guide: To configure how many VLANs will be in GVRP. Example: To configure 200 VLANs in GVRP. Switch# configure

Command Guide of WGSW-48040HP 4.2.43 help Command: help Default: N/A Usage Guide: To explain how to use commands. Example: To explain how

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# hostname planetbestswitch planetbestswitch(config)# 4.2.45 interface * | G

Command Guide of WGSW-48040HP 4.2.45.92 qos pcp...

Command Guide of WGSW-48040HP Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list action permit 4.2.45.2 access-list act

Command Guide of WGSW-48040HP Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list logging 4.2.45.4 access-list policy Co

Command Guide of WGSW-48040HP Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list port-state 4.2.45.6 access-list rate-l

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list redirect inte

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # aggregation group 7 4.

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # do show aaa console : lo

Command Guide of WGSW-48040HP force-unauthorized Port access is not allowed mac-based Switch authenticates on behalf of the

Command Guide of WGSW-48040HP 4.2.45.15 dot1x radius-vlan Command: dot1x radius-vlan dot1x IEEE Standard for port-based Network A

Command Guide of WGSW-48040HP 4.2.45.17 duplex Command: duplex auto | full | half duplex Interface duplex auto Auto negotiation of dupl

Command Guide of WGSW-48040HP 4.2.45.19 excessive-restart Command: excessive-restart excessive-restart Restart backoff algorithm after 16 coll

Command Guide of WGSW-48040HP 4.2.45.133 switchport voice vlan security...

Command Guide of WGSW-48040HP 4.2.45.21 flowcontrol Command: flowcontrol off | on flowcontrol Traffic flow control. off Disable flow

Command Guide of WGSW-48040HP 4.2.45.23 green-ethernet short-reach Command: green-ethernet short-reach green-ethernet Green ethernet (Power

Command Guide of WGSW-48040HP 4.2.45.25 gvrp leave-request vlan Command: gvrp leave-request vlan <vlan_list> gvrp Enable GVRP

Command Guide of WGSW-48040HP 4.2.45.27 ip arp inspection logging Command: ip arp inspection logging all | deny | permit arp Address Resol

Command Guide of WGSW-48040HP Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip arp inspection trust

Command Guide of WGSW-48040HP Switch (config-if) # ip igmp snooping filter 1 4.2.45.31 ip igmp snooping immediate-leave Command: ip igmp snooping i

Command Guide of WGSW-48040HP 4.2.45.33 ip igmp snooping mrouter Command: ip igmp snooping mrouter [ automatic | fix | none ] mrouter Multicast

Command Guide of WGSW-48040HP 4.2.45.35 ip verify source limit Command: ip verify source limit <0-2> <0-2> the number of limit De

Command Guide of WGSW-48040HP 4.2.45.37 ipv6 mld snooping immediate-leave Command: ipv6 mld snooping immediate-leave Default: Disabled Usage Guid

Command Guide of WGSW-48040HP Command: ipv6 mld snooping mrouter [ automatic | fix | none] mrouter Multicast router port configuration automatic

Command Guide of WGSW-48040HP 4.2.53.5 default-router...

Command Guide of WGSW-48040HP 4.2.45.41 lacp key Command: lacp key <1-65535> | auto lacp Enable LACP on this interface key

Command Guide of WGSW-48040HP Switch (config-if) # lacp port-priority 555 4.2.45.43 lacp role Command: lacp role active | passive lacp Enable

Command Guide of WGSW-48040HP To enable LACP timeout type (slow) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface Gigabi

Command Guide of WGSW-48040HP N/A Usage Guide: To apply MED Media-VLAN policy of LLDP for specific interface Example: To apply MED Media-VLAN polic

Command Guide of WGSW-48040HP lldp LLDP configurations receive Enable/Disable decoding of received LLDP frames. Default: Both (Tx

Command Guide of WGSW-48040HP lldp tlv-select port-description lldp LLDP configurations tlv-select To transmit which optional TLVs. port-d

Command Guide of WGSW-48040HP lldp tlv-select system-description lldp LLDP configurations tlv-select To transmit which optional TLVs. syst

Command Guide of WGSW-48040HP Command: lldp transmit lldp LLDP configurations transmit Enable/Disabled transmision of LLDP frames. De

Command Guide of WGSW-48040HP loop-protect action [log] [shutdown] loop-protect Loop protection configuration action Action if loop detected

Command Guide of WGSW-48040HP Command: loop-protect tx-mode loop-protect Loop protection configuration tx-mode Actively generate PDUs Defaul