Planet WNAP-1110 User Manual download pdf

Note

– 1 – – 2 –

– 3 – – 4 –

1. Package Contents

2. Physical Installation

3. Hardware Installation

– 7 – – 8 –

4. Wired Network Configuration (Windows 7)

– 5 – – 6 –

Front Panel Description

Rear Panel Description

WNAP-1110

Quick Guide

CD-ROM

PoE Injector 1 x 4dBi Antenna9V Power Adapter

You have already finished the configuration of the WNAP-1110. Now you

can use your iPhone, iPad, laptop, and any other Wi-Fi device to connect

with it wirelessly and start surfing the internet.

FURTHER INFORMATION:

The above steps introduce simple installations and configurations for the

WNAP-1110. For further configurations of different Operation Modes,

please refer to the user’s manual in the CD. If you have further

questions, please contact the local dealer or distributor where you

purchased this product.

2011-E10350-001

Thank you for choosing PLANET WNAP-1110. Before installing, please

verify the contents inside the package box.

The WNAP-1110 should contain the following items in the package:

If there is any item missing or damaged, please contact the

seller immediately.

Step 1: Locate the WNAP-1110 in an optimum place, and adjust the

antenna for the best coverage.

Step 4: Once the basic configuration is done. Click “Finish /

Reboot” button to make the change to take effect.

Step 3: After you enter into the Web User Interface, click Quick

Setup at the left hand side of the screen.

Please follow the indications on the screen to quickly set up

for the wireless connection.

1. Click “Start” button located at the lower-left corner of your

computer.

2. Click “Control Panel”.

3. Double click “Network and Sharing Center” icon.

4. Click “Change Adapter Settings”.

5. Double click “Local Area Connection”.

6. Select “Internet Protocol Version 4(TCP/IPv4)” and click

“Properties”.

7. Select “Use the following IP address”, and then click “OK”

button twice to save the configuration. For example, as the default

IP address of the WNAP-1110 is 192.168.1.253 and the xDSL

router is 192.168.1.254, you may choose from 192.168.1.1 to

192.168.1.252.

Step 1: The Web management allows you to access and manage the

WNAP-1110 easily. Launch the Web browser and enter the

default IP address http://192.168.1.253

Default IP Address: 192.168.1.253

Default User Name: admin

Default Password: admin

Default SSID: WNAP-1110

Default Wireless Password: PIN code (refer to the label on the

bottom of the WNAP-1110.)

A computer with wired Ethernet connection is required for the first-time

configuration of the WNAP-1110.

5. Enter into the Web Management

Step 2: Highlight the wireless network (SSID) to connect and click

[Connect] button.

WNAP-1110

Quick Installation Guide

150Mbps 802.11n Wireless

Range Extender

Wireless LED

WPS LED

WPS ButtonPower LED

System LED

LAN LED

WPS

WNAP-1110

LAN WLANSYSPWR WPS WPS

4dBi Antenna

10/100Mbps LAN Port

Reset Button

(Press and hold the Reset button for

about 5 seconds for factory default)

Power ON/OFF Button

Power Connector

9V DC Input

POWER ON/OFF LAN

Reset

POWER ON/OFF LAN

Reset

Method A: Hard to find the power socket

Method B: Power Socket nearby

Step 2: When the login window pops up, please enter the User

Name and Password. The default User Name and Password

are both “admin”.

Then click OK button to continue.

For security reasons

it is recommended to

change the password

at the first login and

memorize it.

6. Wireless Network Connection

Step 1: Right-click on the network icon displayed in the system

tray.

Step 3: Enter the encryption key of the WNAP-1110 if necessary.

Step 2: Connect the Power Source to the WNAP-1110. Only choose

one of the following methods for the suitability of AP’s

location; otherwise, it will cause damage to the WNAP-1110.

Method A: Hard to find the power socket

(1) Connect the Ethernet cable into the LAN port of the PC, and plug

the other end of the Ethernet cable into the LAN port of the PoE

Injector.

(2) Use another Ethernet cable (8-wire patch cable) to connect the

LAN port of the WNAP-1110 and the PoE port of the PoE Injector.

 The 8-wire patch cable should not exceed 30 meters in length.

(3) Connect the power adapter into the DC port of the PoE Injector,

and plug the other end of the power adapter into an electrical

outlet.

Method B: Power Socket nearby

(1) Connect the Ethernet cable into the LAN port of the PC, and plug

the other end of the Ethernet cable into the LAN port of the

WNAP-1110.

(2) Connect the power adapter into the POWER port of the

WNAP-1110 in the rear panel, and plug the other end of the

power adapter into an electrical outlet.

POWER ON/OFF LAN

Reset

Power

PoE Injector

POWER

PoE

LAN

POWER ON/OFF LAN

Reset

POWER

PoE

LAN

Power

Check connection before powering on. Wrong connection

may cause device malfunction, say, your PC or other

Ethernet device.

Caution

1 2

Summary of Contents

Page 1 - Range Extender

Note– 1 – – 2 –– 3 – – 4 –1. Package Contents2. Physical Installation3. Hardware Installation– 7 – – 8 –4. Wired Network Configuration (Windows 7)– 5

Page 2

Note– 1 – – 2 –– 3 – – 4 –1. Package Contents2. Physical Installation3. Hardware Installation– 7 – – 8 –4. Wired Network Configuration (Windows 7)– 5

Planet WNAP-1110 User Manual

Browse online or download User Manual for Routers Planet WNAP-1110. PLANET WNAP-1110 User Manual

Summary of Contents

More documents for Routers Planet WNAP-1110

Comments to this Manuals

Planet WNAP-1110 User Manual

Browse online or download User Manual for Routers Planet WNAP-1110. PLANET WNAP-1110 User Manual

Summary of Contents

More documents for Routers Planet WNAP-1110

Comments to this Manuals

Related products and manuals for Routers Planet WNAP-1110