Note
– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
2. Installation Precautions
3. Physical Introduction
– 7 – – 8 –
– 5 – – 6 –
The above steps introduce the simple installations
and configurations of the WNAP-6315. For further
configurations, please refer to the user manual
which you can download from the website.
http://www.planet.com.tw/en/support/download.p
hp?type1=4&model=48686&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product.
2011-E10620-000
Thank you for choosing PLANET WNAP-6315. Before installing the
AP, please verify the contents inside the package box.
If there is any item missing or damaged, please
contact the seller immediately.
Step 3: Plug the power cord into the DC port and plug the
other end of the RJ45 cable into the POE port of the
PoE injector (See Step 2).
Step 1: Push the latch on the bottom of the WNAP-6315 and
slide down the cover to remove.
Bottom Panel Description – Port
Connect the WNAP-6315 with your PC via an Ethernet cable
plugging into LAN port of PoE injector on one end and into LAN
port of PC on the other end. Power on the WNAP-6315 via PoE
from PoE injector.
1. Click the “Start” button located in the lower-left corner of
your computer.
2. Click “Control Panel”.
3. Double-click “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and
click “Properties”.
7. Select “Use the following IP address”, and then click
the “OK” button twice to save the configuration. For
example, as the default IP address of the WNAP-6315 is
192.168.1.253 and the router is 192.168.1.254, then you
may choose from 192.168.1.1 to 192.168.1.252.
Default IP Address: 192.168.1.253
Default User Name: admin
Default Password: admin
Default SSID: WNAP-6315
Step 1: The Web management allows you to access and
manage the wireless AP easily. Launch the Web
browser and enter the default IP address
http://192.168.1.253.
WNAP-6315
Quick Installation Guide
150Mbps 802.11n Wireless Outdoor CPE
For security reasons, it is recommended to change the
password at the first login and memorize it.
Step 2: When the login window pops up, please enter the
User Name and Password. The default User Name
and Password are both “admin”. Then click the OK
button to continue.
Step 3: After you enter into the Web User Interface, click
Smart Setup Wizard at the left hand side of the
screen. Once the basic configuration of the AP is
done. Click the Finish or Apply button to make the
change take effect.
Rear Panel Description – LED Indication
4. Hardware Installation
Step 1: Place the strap through the slot on the back of the
WNAP-6315 and then around the pole. Tighten the
strap to secure the WNAP-6315.
5. Pole Mounting
Further Information:
6. Web Login
1 2
3 4
Step 4: Successful installation.
Step 2: Plug the RJ45 Ethernet cable into the PoE LAN Port of
the WNAP-6315. Then, slide back the cover of the
WNAP-6315 to finish the installation.
IMPORTANT SAFETY PRECAUTIONS:
1. LIVES MAY BE AT RISK! Please be aware of the
electrical wires around, and tighten the pole.
Carefully read the section "OUTDOOR
INSTALLATION WARNING" in the manual
before installation.
2. Users MUST use the “PoE Injector” and
“Power Adapter” shipped in the box with the
WNAP-6315. Otherwise, the product might be
damaged.
3. Users MUST use a proper and well-installed
surge arrestor and grounding wired with the
WNAP-6315; otherwise, a sudden lightning could
cause fatal damage to the WNAP-6315. EMD
(Lightning) DAMAGE IS NOT COVERED
UNDER WARRANTY.
Caution
WNAP-6315
Plastic Strap x 1
PoE Injector
LAN 1 LEDWireless LED
Power LED LAN 2 LED
To LAN Switch or PC
To WNAP-6315
Power Adapter
Quick Guide
Optional RP-SMA Connector
LAN2
PoE LAN
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals