Planet GTP-80x Series User Manual

1000Base-X to 10/100/1000Base-T802.3at PoE Media ConverterGTP-802 / GTP-802S / GTP-805AUser’s Manual

10Left ViewThere are one RJ-45 Twisted-Pair jack (Auto-MDI/MDI-X), one ber-optic connector (vary by model) and four LED indicators.Figure 4-3:

115. Link Fault Pass Through (LFP)The LFP function includes the Link Fault Pass Through function (LLCF/LLR) and the DIP Switch design.

12If the connection breaks, GTP-80X that link loss forward to the Switch / Hub that generates a trap to the management station. Th

13If one of the optical conductors is down (as shown in the diagram box below), the converter with LLR function will return a no-

146. Installing the ConverterPlease follow these steps to install the PoE+ Media converter:Turn off the power of the device / station in a

151000Base-SX/LXSFP transceiver1000Base-SX/LXLC Fiber10/100/1000Base-T UTPFigure 6-2: GTP-805A InstallationNoteRJ-45 / STP, UTP Cat5 / 5e / 6

167. PoE FunctionGTP-80X and the IEEE 802.3at / 802.3af Injector / Splitter equipment installation:Before your installation, it is recomm

17For the places where are hard to nd the power inlet, the GTP-80X provide the easiest way to power your Ethernet devices such as PLANET

188. LED IndicationSystemLED Color FunctionPWR Green Light Indicate the device is powered.10/100/1000Base-T PortLED Color FunctionLNK/ACT GreenBlinkIn

199. Cable Connection ParameterThe limitations are as below:Duplex Connection Limitation (max.)Twisted PairHalf / FullNode to NodeNode to Switch/Hub1

TrademarksCopyright © PLANET Technology Corp. 2011.Contents subject to revision without prior notice.PLANET is a registered trademark of PLANET

2010. GTP-80X Technical SpecicationsThe GTP-80X comes with the following standard features:lStandard: IEEE 802.3 / 802.3u / 802.3ab, 10/100/1000Base

21APPENDIX AA.1 Device's RJ-45 Pin Assignments1000Mbps, 1000Base-TRJ-45 Connector pin assignmentContact MDI MDI-X1 BI_DA+ BI_DB+2 BI_DA- BI_DB-3

22A.2 RJ-45 Cable Pin AssignmentThere are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocati

23A.3 Fiber Optical Cable Connection ParameterThe wiring details are as below:Fiber Optical Patch Cables:Standard Fiber Type Cable Specication1000Ba

EC Declaration of ConformityFor the following equipment: *Type of Product: 1000Base-SX/LX/X to 10/100/1000Base-T PoE Media Converter *Model Number

FCC WarningThis equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part

WEEE WarningTo avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrica

Table of Contents1. Overview ... 6 About the Power over Ethernet Injector ...

61. OverviewThank you for purchasing PLANET GTP-80X family 1000Base-X Fiber-optic to 10/100/1000Mbps Ethernet Twisted pair 802.3at PoE B

72. Model ListYour 802.3at PoE Media Converter comes with three of the following models.GTP-802: l Multi-Mode SC interface ber connector, u

83. ChecklistYour GTP-80X box should contain the following items:1000Base-X to 10/100/1000Base-T 802.3at PoE Media lConverter x 1User’s Manual x

94. Product OutlookOverviewThe layout of GTP-802 is the same as for GTP-802SFigure 4-1: Product Outlook of GTP-802/GTP-802SThe layout of GTP-805A52V~